Monster Mobile MST701 Manuel D'opération page 2

FAILURE TO OBSERVE THESE WARNINGS COULD RE SULT IN IN JU RY.
This insTrucTion Manual conTains iMporTanT safeTy
inforMaTion.
read This insTrucTion Manual carefully and undersTand
all inforMaTion Before operaTing This Tool.
• Read and understand all instructions. Failure to follow
all instructions listed below, may result in electric
shock, fire, explosion and/or serious personal injury. It is
the responsibility of the owner to make sure all personnel
read this manual prior to using the device. It is also
the responsibility of the device owner to keep this
manual intact and in a convenient location for all to
see and read. If the manual or product labels are lost
or not legible, contact Monster Mobile for replacements.
If the operator is not fluent in English, the product
and safety instructions shall be read and discussed
with the operator in the operator's native language by
the purchaser/owner or his designee, making sure that
the operator comprehends its contents.
• Always operate, inspect and maintain this tool in
accordance with American National Standards Institute
Safety Code of Portable Air Tools (ANSI B186.1) and any
other applicable safety codes and regulations.
• For safety, top performance and maximum durability of
parts, operate this tool at 90 psig; 6.2 bar max air
pressure with 3/8" diameter air supply hose.
• Always wear impact-resistant eye protection and face
protection when operating or performing maintenance on
this tool (users and bystanders).
• High sound levels can cause permanent hearing loss.
Always use hearing protection as recommended by your
employer an OSHA regulations while using this tool
(users and bystanders).
• Keep the tool in efficient operating condition.
• Operators and maintenance personnel must be
physically able to handle the bulk, weight and power of
this tool.
• Air under pressure can cause severe injury. Never direct
air at yourself or others. Always turn off the air supply,
drain hose of air pressure and detach tool from air supply
before installing, removing or adjusting any accessory
on this tool, or before performing any maintenance on
this tool. Failure to do so could result in injury. Whip
hoses can cause serious injury. Always check for
damaged, frayed or loose hoses and fittings, and replace
immediately. Do not use quick detach couplings at tool.
See instructions for correct set-up.
• Keep tool out of reach of children.
• Air powered tools can vibrate in use. Vibration, repetitive
motions or uncomfortable positions over extended
periods of time may be harmful to your hands and arms.
Discontinue use of tool if discomfort, tingling feeling or
pain occurs. Seek medical advice before resuming use.
• Slipping, tripping and/or falling while operating air
tools can be a major cause of serious injury or
death. Be aware of excess hose left on the walking
or work surface.
• Keep body working stance balanced and firm. Do
not overreach when operating the tool.
• Note direction of rotation BEFORE operating this tool.
MST701
WARNING
• Anticipate and be alert for sudden changes in motion
during start up and operation of any power tool.
• Do not carry tool by the hose. Protect the hose from
sharp objects and heat.
• Tool shaft may continue to rotate briefly after throttle is
released. Avoid direct contact with accessories during
and after use. Gloves will reduce the risk of cuts or
burns.
• Keep away from rotating end of tool. Do not wear
jewelry or loose clothing. Secure long hair. Scalping
can occur if hair is not kept away from tool and
accessories. Choking can occur if neckwear is not
kept away from tool and accessories.
• Do not use (or modify) the tool for any other purpose
than that for which it was designed without consulting
the manufacturer's authorized representative.
• Correct bonded abrasive mounted point grinding wheels,
rotary files and carbide burrs are necessary to prevent
injury from broken accessories. Do not use chipped or
cracked bonded abrasive mounted point grinding
wheels, rotary files and carbide burrs. Tighten the
bonded abrasive mounted point grinding wheels, rotary
files and carbide burrs on the collet to prevent spin off
RPM RPM RPM
when the Die Grinder is turned off.
• RPM OF THE ACCESSORY MUST EXCEED TOOL RPM. Use
accessories rated at
• Never mount a grinding wheel, cut-off wheel, router
cutter or drill bit on a Die Grinder.
• Never use an arbor, mandrel or any other adaptor to
convert the Die Grinder for any other application.
• Do not lock, tape or wire the "on/off" safety lever in the
"on"position, as the lever must be free to return to the
"off" position when released.
• Use replacement parts and accessories recommended by
Monster Mobile.
• Do not lu b ri c ate tools with flam m a b le or vol a t ile liq u ids
such as ker o s ene, die s el or jet fuel.
• This tool is not insulated against electric shock.
• This tool must not be used in explosive atmospheres.
• Servicing and repairs should only be made by an
authorized service center.
• Do not force tool beyond its rated capacity.
• Do not remove any labels. Replace damaged labels.
• This product may contain one or more chemicals known
to the State of California to cause cancer and birth
defects or other reproductive harm. Wash hands
thoroughly after handling.
• Failure to heed these warnings may result in serious or
fatal personal injury and/or property damage.
2
25,000 RPM or higher.
10/05/15