First Use - Jupiter Nutrimix Mode D'emploi

• In the right-hand part of the display, the elapsed pro-
cessing time or the time remaining on the current pro-
gram is displayed in minutes (
operation.
PULSE
• Tapping activates the PULSE function from standby
mode.
 flashes
• Within 30 s you can then switch the speed of the blade
to level 10 by pressing
 A brief signal tone is sounded and all 10 points of the
manual speed setting are lit up brightly.
The PULSE function only remains active for as long
Info:
as you press .
• The processing time elapsed is shown on the LCD dis-
play.
Info:
• After using the PULSE function for 10 minutes, the ap-
pliance switches off automatically.
 Standby mode, flashes red
• Executing the PULSE function stops the running process
and the appliance switches off after the PULSE function
is ended.
 Standby mode, flashes red
Cleaning program
( see Page 13)
Program description
• Tapping activates the cleaning program from standby
mode.
 flashes
• Within 10 s you can then start the cleaning program by
pressing .
 lights up brightly
• When the program ends, a short signal tone is sounded
and the appliance automatically switches off.
 Standby mode, flashes red
• You can manually end the cleaning program at any time
by tapping .
 Standby mode, flashes red
Program symbols S
( see Page 13).
Program description
• Tapping the program symbols activates the correspond-
ing program from standby mode.

The selected program symbol flashes
• Within 10 s you can then start the corresponding pro-
gram by tapping .
 lights up brightly
• When the program ends, a short signal tone is sounded
and the appliance automatically switches off.
 Standby mode, flashes red
Subject to technical changes without notice; no responsibility is accepted for the accuracy of this information.
) and seconds ( ) during
m s
again and holding it.
• You can manually end the program at any time by tap-
ping .
 Standby mode, flashes red
Manual speed setting T
• By tapping the individual point, you can preselect the
speed of the blade in levels from 1 - 10 from standby
mode.
 All points up to the preselected level light up brightly.
Speed min.
1
• Within 10 s you can then start processing by tapping
.
• The speed level and the processing time elapsed are
shown on the LCD display.
• You can end processing at any time by tapping

Standby mode, flashes red
Info:
• After a processing time of 10 minutes, the appliance
switches off automatically.
 Standby mode, flashes red
• The speed can be changed at any time by selecting a
different speed level.

First use

• Ensure that the appliance's mains plug is plugged out.
• Before using the appliance for the first time, thoroughly
clean all parts of the appliance (see section
• Always ensure that the appliance is completely assem-
bled before operating it, with the container lid
and the sealing cap
in place
ternatively, the tamper provided can be inserted in the
container lid instead of the sealing cap.
• Place the appliance on a non-slip, even and clean sur-
face.
Switching on and setting the appliance
CAUTION Rotating parts can cause injury!
• Never put your hand into the appliance when the motor
is running.
CAUTION Risk of injury from the container wall
becoming hot, from hot splashing food-
stuffs and hot steam!
• At cooking temperatures above 60 °C, foodstuffs that
spit or splash out, and any contact with the walls of the
container can lead to burns.
• Do not exceed the maximum fill quantity of the con-
tainer. The maximum fill quantity is marked on the wall
of the container (1500 ml, marked
• Make sure when removing the container that none of
the hot contents can escape.
10
Max. speed
.
).
Cleaning
seal
and
! Al-
in place and locked
MAX ).
11