Casals AG115500 Notice Originale page 8

Fitting the accessories
Unplug the appliance from the mains.
Block the spindle (F) by pressing the Spindle
blocking button (E). The spindle must be stopped
before press-ing the spindle blocking button.
With the Tightening key (K) remove the clamping
nut (J) from the spindle (F).
Assemble the tool on the support plate (H).
Assemble the clamping nut (J) using the tightening
key (K). The position of the clamping nut (J) will
depend on the thickness of the tool (see fig 3 and
4).
Once the tool is assembled check if the spindle
block-ing button (E) has return to its original posi-
tion.
Use:
Connect the appliance to the mains.
Turn the appliance on, by using the on/off switch.
Be careful of the shavings that fly off. Hold the tool
that so the sparks fly away from you, other people
or inflammable materials.
When carrying out grinding operations, it is advis-
able that the angle between the surface and the
disc is ap-proximately 15º - 30º for the best results.
When cutting, do not press on the disc. The discs
should not move sideways or oscillate. The tool
should advance smoothly at the beginning and
later moderate-ly and adapted to the type of mate-
rial. The tool should move in the opposite direction
to the advance of the disc, never in the same
direction, as there would be a risk of the machine
dumping out of the cutting line in an uncontrolled
manner.
Once you have finished using the appliance:
Stop the appliance by releasing the on/off switch.
Cleaning
Disconnect the appliance from the mains and allow
it to cool before undertaking any cleaning task.
Clean the electrical equipment and the mains
connec-tion with a damp cloth and dry. DO NOT
IMMERSE IN WATER OR ANY OTHER LIQUID.
Clean the equipment with a damp cloth with a few
drops of washing-up liquid and then dry.
Do not use solvents, or products with an acid or
base pH such as bleach, or abrasive products, for
cleaning the appliance.
Do not let water or any other liquid get into the air
vents to avoid damage to the inner parts of the
appli-ance.
Never submerge the appliance in water or any
other liquid or place it under running water.
- If the appliance is not in good condition of cleanli-
ness, its surface may degrade and inexorably af-
fect the du-ration of the appliance's useful life and
could become unsafe to use.
Supplies
Always use original supplies, designed specifically
for your appliance model.
These supplies are available in specialist shops.
Anomalies and repair
Take the appliance to an authorised technical sup-
port service if a product damage or other problems
arise. Do not try to dismantle or repair without
assistance, as this may be dangerous.
If the connection to the mains has been damaged,
it must be replaced and you should proceed as you
would in the case of damage.
Specifications: AG115500
Rated Power:
Rated Voltage:
No load Speed
Max. disc diameter
Spindle thread
Weight:
Sound Pressure level
Sound Power level
Vibration
NB: These specifications are subject to change
without notice of purpose of improvement.
NB: By virtue of the conditions of fabrication of this
product, the maximum absorbed power can differ
from that specified.
NB: By virtue of the conditions of fabrication of this
product, the maximum used power can differ from
that specified.
Wear hearing protection
Measured sound level determined according
EN60745.
The vibration emission level given in this informa-
tion sheet has been measured according EN60745
and may be used to compare one tool with other.
It may be used for a preliminary assessment of
exposure.
The vibration value during actual use of the power
tool can differ from the declared total value de-
pending on the way in which tool is used.
-It's necessary identify safety measures to protect
the operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it
is running idle in addition to the trigger time)
500W
230V-240V~
11.000 rpm
115 mm
M14
2.1 Kg
< 86dB(A)
< 97dB(A)
<3.43 m/s2 K=1.5m/s2