Product Description; Safety Instructions - Conrad 75 15 11 Mode D'emploi

O P E R A T I N G I N S T R U C T I O N S
2.4 GHz Digital Camera
Item-No. 75 15 11
Intended use
The camera is for monitoring and protecting secluded or critical areas (e.g. monitoring
stores, intercommunication systems, entrances and so on). The camera serves as an
accessory camera that is suitable for use with the set with item no. 751509.
The camera complies with protection category IP44 and is therefore appropriate for
outdoors areas.
The voltage is supplied via the provided power transformer (5 V/DC, 1 A).
Please bear in mind that it is prohibited by law to observe strangers with a camera
without their knowledge and consent.
Operating the product in any other way than described above is not permitted and
may lead to damage to the product, which can give rise to risks such as short circuit,
fire and electric shock. The product must not be modified or converted. Always
observe the safety instructions included in these operating instructions. Read the
operating instructions carefully and keep them for later reference.
Included in the Delivery
• 2.4 GHz Digital Camera
• Camera support
• Installation material
• Power supply unit
• Operating Instructions
Symbols
A lightning-bolt symbol in a triangle indicates a health hazard, e.g. danger
of electric shock.
The exclamation mark in a triangle indicates a particular risk in handling,
operating and control.
The "Hand" symbol indicates special tips and operating information.

Safety Instructions

The warranty will be void in the event of damage caused by failure to
observe these safety instructions! We will not assume any responsi-
bility for consequential damage! We shall not accept liabilityfor
damage to property or personal injury caused by incorrect handling
or non-compliance with the safety instructions. The warranty will be
void in such cases.
The exclamation mark indicates important information in these oper-
ating instructions that should always be observed.
• The camera must not be modified or converted, as not only the CE certification will
become void but also the warranty.
• The camera should not be exposed to extreme temperatures, direct sunlight,
intense vibration or heavy mechanical stress.
• The use of the surveillance camera system does not replace the personal supervision
of children, or people who require special assistance, but only serves as a support to
this supervision.
• This camera system uses and generates high frequency energy. If the devices are
not installed and operated in accordance with these instructions, they can cause
radio interference. If a radio camera system causes interference to other devices,
try one or more of the following measures listed below, in order to restore normal
function:
- Change the position of the camera.
- Increase the distance between the device affected and the radio camera or the
receiver for the radio camera system
- Select another transmission channel.
• After rapid changes in temperature, the camera requires approx. 15 minutes to sta-
bilise, to adjust to the surrounding temperature, before it can be used.
• This device is not a toy and should be kept out of the reach of children!
• The transformer conforms to protection class II. It may only be plugged into a standard
household 230V~/50Hz mains supply socket.
• Please contact a qualified person if you are unsure about the safety and correct use
of the camera.
• Never let the packaging material lie around unattended. Plastic foil /bags etc can be
dangerous toys for children, there is a risk of suffocation.
www.conrad.com
• If you have reason to assume that safe operation is no longer possible, disconnect
the device immediately and secure it against inadvertent operation.
Version 06/09
°
• It can be assumed that safe operation is no longer possible if:
- the device is visibly damaged,
- the device no longer works and
- the unit was stored under unfavourable conditions for a long period of time or
- if it has been subjected to considerable stress in transit.
• In commercial institutions, the accident prevention regulations of the Employer's
Liability Insurance Association for Electrical Systems and Operating Materials are to
be observed.
• The mains transformer may only be used indoors, in dry rooms.
• The radio camera is suitable for operation in outdoor areas (IP44).
• Maintenance, adjustment and repair may only be carried out by a qualified specialist
or a specialised repair shop.
• If you have any questions, which are not answered in this manual, please contact
our technical service or an other specialist.

Product Description

1) Antenna
2) LED connection
3) Power LED
4) Camera lens
5) IR LED
Assembly
Find a suitable place for mounting, from which the area to be monitored can be
observed.
A suitable place for installation of this camera has the following features:
• Vibration free
• No direct sunlight
The above-mentioned can seriously disturb the radio transmission or limit its range.
Mounting the radio camera
• Seek out a suitable location for mounting the camera.
• There are three mounting holes on the "camera support" (7). Mark these (e.g. with
a pencil) on the wall.
6) Photo sensor
7) Camera support
8) DC IN 5 V/DC 1A
9) Pairing Key
10) Microphone
Select a place for mounting which is not shielded, for example, by rein-
forced concrete walls, silvered mirrors or metal shelves. There should be
no devices with strong electrical fields, such as mobile telephones,
radios or electrical motors, close to the device.
None of the connection cables must be bent nor squeezed. This can
result in malfunctions, short circuits and defects in the device.
Make sure that cables are not damaged, when drilling or bolting into
place. Ensure that the plug and socket of the camera's connection
cable are not exposed to damp. Plugs and sockets may only be used
indoors. Therefore, the cable from the camera (for installation in out-
door areas or in damp rooms) must be placed so that it is led into a
dry room.