Taymor LUNA 06-4629P Instructions D'installation

INSTALLATION INSTRUCTIONS
LUNA 06-4629P
SINGLE HANDLE LAVATORY FAUCET
THIS FAUCET MEETS OR EXCEEDS THE FOLLOWING STANDARDS:
ASME A112.18.1/CSA B125.1 and NSF-61
THANK YOU FOR PURCHASING THIS TAYMOR PRODUCT. ALL TAYMOR PRODUCTS ARE CAREFULLY
ENGINEERED AND FACTORY TESTED TO PROVIDE LONG TROUBLE-FREE USE UNDER NORMAL CONDITIONS.
HAVE BASIC TOOLS READY
1
RECOMMENDED TOOLS:
Teflon tape Screwdrivers Adjustable Flashlight
wrench and
pipe wrench
WARNING: READ ALL the instructions completely before beginning.
READ ALL warnings, care and maintenance information.
Taymor recommends calling a professional if you are uncertain about installing this product!
This product should be installed in accordance with all local and provincial plumbing and building codes.
Need Help? Please call our toll-free Customer Support line at
(WEST) 1-800-267-4774 (EAST ) 1-800-387-7064 for additional assistance or service.
TURN OFF THE MAIN WATER SUPPLY
2
Locate water supply inlets and shut off water supply valves. These are usually found under
the sink.
TURN OFF
3 FAUCET INSTALLATION
1a) With Escutcheon. Apply a bead of plumber's putty or silicone caulk around the sink openings. Install the
gasket over the three holes in your sink.
1b) Install faucet hoses through the hole of the sink. Centre the faucet body. Make sure that handle is properly
aligned to sink.
1c) From underneath the sink, secure base plate to faucet with screws (1) and secure faucet to sink with mounting
nuts (1) provided.
2a) With Flange. Place flange (1) on the bottom of faucet. Place faucet through mounting hole in sink.
2b) From underneath the sink, secure the faucet with washer (1) and nut (2). Do not over tighten.
Don't use plumber's putty on cultured marble or other composite sinks.
Putty will discolour the sink.
1a
2a
1
WITH OPTIONAL ESCUTCHEON
Your installation may require new supply
lines. (Supply lines are not included.)
Safety goggles
Torque wrench Plumber's putty
TURN OFF
1b 1c
2b
3
1
2
ATTACH THE HOT AND COLD SUPPLY LINES
4
Thread the nut (1) on supply line onto outlet of water supply valve (2) and tighten with a wrench.
Do not over tighten.
INSTALLING POP-UP DRAIN
5
A) Remove pop-up plunger (A) and flange (B). Screw locknut (C) all the way down. Push gasket (D)
down. Apply silicone to underside of flange (B).
B) Insert body into sink (from underneath). Screw flange onto body. Pivot hole (E) must face the back
of the sink.
C) Tighten locknut (C) and gasket but do not overtighten. Remove pivot ball retaining nut (E).
D) Slide pivot rod (F) into the eye of the pop-up plunger (A). Hand tighten retaining nut.
E) Slide pivot rod (F) through hole in spring clip (G), then through lever strap (H) and back through
spring clip.
F) Insert lift rod (I) down through faucet body and then into lever strap (H). Tighten screw (J). Connect
assembly to drain.
A
Silicone caulk
C
D
A
IMPORTANT
FLUSHING & AERATOR CLEANING
6
Remove the aerator by turning it counterclockwise.
Remove the internal parts of the aerator by pushing them
out with your fingers. Remove any debris. Turn on hot and
cold water supplies. Turn faucet handle all the way on and
run water through the spout for about a minute to remove
debris. While water is running check all connections for leaks.
Reassemble the aerator and screw it back into the spout, hand tighten.
EXPLODED DIAGRAM FOR REFERENCE
7
MAINTENANCE Your new faucet is designed for years of trouble-free performance. Keep it looking
new by cleaning it periodically with a soft cloth. Avoid abrasive cleaners, steel wool and harsh
chemicals as these will dull the finish and void your warranty.
2 - SET SCREW
1 - HANDLE
8 - AERATOR
ASSEMBLY
1
2
9 - FLANGE
10 - ESCUTCHEON
11 - BASE PLATE
CUSTOMER SERVICE
1
2
B
A
B
B
D
B
E
A
E
F
F
3 - HANDLE SEAT
4 - BONNET
5 - CAP
6 - CARTRIDGE
7 - SPOUT
12 - BOLT
13 - WASHER
14 - MOUNTING NUT
WEST 1-800-267-4774 | EAST 1-800-387-7064 | taymor.com
® REGISTERED TRADEMARK OF TAYMOR INDUSTRIES LTD.
C
E
C
F
I
H
J
H
G
15 - LIFT ROD KNOB
16 - LIFT ROD
17 - POP-UP ASSEMBLY
REV. DEC. 2017