Before Starting The Equipment - Toolson PRO-ST 85 Instructions D'origine

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 24

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
5.1 Safety guard (Fig. 2/Item 15)
The safety guard (15) protects the user from
accidentally touching the saw blade (12) and
nevertheless enables you a free view of the
cutting area.
The safety guard (15) must always be fitted
and in position before starting any sawing
work.
The safety guard (15) can be pulled up as
shown in Fig. 2.
5.2 Changing the saw blade (Fig. 3-4/Item 12)
Danger!
Pull the mains plug before you fit or replace a
saw blade.
Set the selector switch for pendulum action
(8) to position 3.
The teeth of the saw blade are very sharp!
Push the holder for the saw blade (14) to-
wards the tool and insert the saw blade (12)
into the saw blade holder (14) as far as pos-
sible (Figure 3). The teeth on the saw blade
must be pointing forwards.
Allow the blade holder (14) to slide back to
starting position. The saw blade (12) must sit
in the guide roller (10) (Fig. 4).
Check that the saw blade (12) is securely
mounted in the blade holder.
Follow the instructions above in reverse order
to remove the saw blade.
5.3 Installing the parallel stop (Figure 5/ Item
11)
The parallel stop (11) enables you to saw
parallel cuts.
Undo the two locking screws (13) on the so-
leplate (7).
Now slide the parallel stop (11) into the
guides on the soleplate (7). You can fit the
parallel stop (11) on either the left or right of
the equipment.
The guide strip must always face downwards.
Set the required distance using the measu-
rement scale on the parallel stop (11) and
tighten the locking screws (13) again.
Anl_PRO_ST_85_SPK7.indb 18
Anl_PRO_ST_85_SPK7.indb 18
GB
5.4 Setting the soleplate for miter cuts (Figs.
6-7)
Use the Allen key (4) to loosen the screws for
the soleplate (16) on the bottom of the adjus-
table soleplate (7) (Figure 6).
Pull the soleplate (7) slightly forward. The so-
leplate can now be swiveled a maximum 45°
to the left and right.
If the soleplate (7) is pushed back to the
rear again, it will only function in the locking
positions at 0°, 15°, 30° and 45°, which are
marked on the graduated scale for the sole-
plate (9) (Figure 7). Move the soleplate into
the required position and refasten the screw
securing the soleplate (16).
However, the soleplate (7) is also easily set to
another angle. To do so, move the soleplate
(7) forwards, set the desired angle and refas-
ten the screw securing the soleplate (16).
5.5 Adapter for dust extraction system (Figu-
re 8)
Connect your jigsaw to a vacuum cleaner
using the adaptor for dust extraction (6). This
will ensure optimum dust extraction from the
workpiece. The benefits are that you will pro-
tect both the equipment and your own health.
Your work area will also be cleaner and safer.
Dust created when working may be dange-
rous. Refer to the section entitled "Safety
information".
Fit the adapter (6) as shown in Fig. 8. The ad-
apter (6) must audibly engage to ensure that
it is secure in the soleplate (7). The adapter
for chip extraction (6) cannot be used for mi-
ter cuts.
Fit the vacuum tube of the vacuum cleaner
onto the adaptor opening (6). Check that the
connections are air-tight.
6. Operation
6.1 ON/OFF switch (Fig. 9/Item 3)
To switch on:
Press the ON/OFF switch
To switch off :
Release the ON/OFF switch
- 18 -
28.05.15 14:25
28.05.15 14:25

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

43.211.30

Table des Matières