Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
TickiT LED Light Panel Instructions
Getting Started
Position the panel on a flat even surface. Try to avoid
letting the panel overhang, this will prevent tipping if
the edges are leaned upon.
Power Supply
The power supply is multi territory (UK,EU,US,AU).
Select the correct adaptor, slide firmly into position on
the power supply until you hear a "click."
To remove the adaptor, press button (A) with your
thumb and slide the adaptor away.
A
Operation
Plug the DC jack into the panel, then plug into the mains
socket ensuring that the socket is switched on.
The panel has three light level settings (Lo-Med-Hi) plus
an Auto Lock-On feature to avoid the panel from being
turned off accidentally when in use.
Tap
symbol once and the panel will light at its lowest
setting. Tap
once more for the medium setting, then
once again for maximum brightness. To turn off the
panel, tap and hold
for 3 seconds and the panel will
go off.
©2016 TickiT
©2016 TickiT
©2016 TickiT
Products | Commotion House | Morley Road | Tonbridge | Kent | TN9 1RA | England | www.tickitproducts.co.uk
Products | Commotion House | Morley Road | Tonbridge | Kent | TN9 1RA | England | www.tickitproducts.co.uk
Products | Commotion House | Morley Road | Tonbridge | Kent | TN9 1RA | England | www.tickitproducts.co.uk
®
®
®
Product Code: 73046, 73048, 73050, 73052
Important
Use only the TickiT 12V power supply provided.
Using the wrong power supply from another
product may damage your unit beyond repair
and invalidate your warranty.
Avoid using sharp or abrasive objects on the panel.
These will cause scratches on the surface and shorten
the life of the product significantly.
Cleaning should always be carried out by an adult.
Always un-plug and disconnect the power supply before
cleaning, wipe surfaces using a damp cloth, and avoid
chemical, solvent or abrasive cleaners as these may
damage the top surface.
Check the power supply regularly for any damage
to the plug, cable and plastic case. If damaged then
replace the unit immediately.
Do not allow contact with water or other liquids and
do not short circuit the connector. Always switch off or
un-plug the power supply when not in use.
Warnings
Choking Hazard: This product has small parts and is not
suitable for children under 36 months.
Power Supply: This is not a toy.
Please retain this information for future reference.
Publicité
Sommaire des Matières pour TickiT 73046
- Page 1 Getting Started Important Position the panel on a flat even surface. Try to avoid Use only the TickiT 12V power supply provided. letting the panel overhang, this will prevent tipping if the edges are leaned upon. Using the wrong power supply from another product may damage your unit beyond repair and invalidate your warranty.
- Page 2 Code produit : 73046, 73048, 73050, 73052 Mode d’emploi du panneau TickiT à éclairage LED Guide de démarrage Important Placer le panneau sur une surface entièrement plate. N’utiliser que le bloc d’alimentation 12 V Essayer d’éviter que le panneau soit en porte-à-faux, fourni par TickiT.
- Page 3 Erste Schritte Wichtig Platzieren Sie die Leiste auf einer flachen, ebenen Verwenden Sie nur das von TickiT mitgelieferte Oberfläche. Vermeiden Sie ein Überhängen der Leiste, 12-V-Netzteil. Wenn Sie ein Netzteil eines da sie sonst bei Belastung der Kanten kippen kann.
- Page 4 Coloque el panel sobre una superficie lisa y plana. Procure evitar que el panel sobresalga de la superficie para TickiT de 12V provisto. El uso del suministro de prevenir que se vuelque si alguien se apoya en los bordes. potencia de otro producto podría dañar su unidad irreparablemente e invalidar la garantía.