BASETech Head Up Display X5 Mode D'emploi page 4

Settings
For the displayed values of the head up display to match the values shown in your dashboard, it may be nec-
essary to adjust them. Furthermore, different settings can be made for the operation of the head up display.
The adjustments are made with the function switch (3):
• Press the function switch (3) for five seconds > Opening or closing of the setup menu
• Press the function switch (3) briefly > Go to the next option
• Move the function switch (3) forwards or backwards > Changes the set values
Procedure
• Open the setup menu by holding the function switch (3) pressed for five seconds.
• Set the options in the list below as desired.
• Press the function switch (3) again for five seconds to leave the setup menu again.
Option Setup range
Adjustment of the speed
50-150
display
Adjustment of the
50-150
engine speed display
Engine speed warning 10-99
Speed warning 30-250
Adjustment of display
0-2
brightness
Speed unit 1-2
Temperature unit 1-2
Automatic
10-900
switch-off
W hen setting or adjusting the speed display and engine speed display, please approximate the
actual display of the instruments in the vehicle step by step. It may be necessary to try a few
values.
Operation
D o not operate the device when driving as this distracts you from traffic and will also put
other road users at risk.
During normal use of the vehicle, the head up display does not need to be switched off
manually. It switches off automatically, when the engine is not running. It will then only
consume a small amount of power but this will not affect the car battery significantly.
However, if you do not use your vehicle for a longer period of time, switch off the head up
display manually (move on/off switch (2) into position OFF) to avoid using the car battery
unnecessarily when the vehicle is not in use.
• Normally, the head up display shows the moving speed and the engine speed.
• Press the function switch (3) briefly to display the values for coolant temperature, battery voltage and then
speed again.
• To reset the settings to the default, switch off the head-up display (turn the ON/OFF switch (2) to the OFF
position). Press and hold the function button (3) and switch on the head-up display (turn the ON/OFF
switch (2) in the ON position). The display shows RES and all lights light up briefly.
• Rotate the function switch (3) back and hold for five seconds to switch the warning sounds on or off.
Maintenance and Cleaning
• Switch off the product every time before cleaning (move on/off switch (2) into position OFF).
• Absolutely prevent wetness or dampness from penetrating into the device.
• Never use aggressive cleaning agents, cleaning alcohol or other chemical solutions, since these could
damage the housing or reflective film or even impair operation of the head up display.
• Use a dry, lint-free cloth to clean the product. If the device is very dirty, use a cloth slightly moistened with
lukewarm tap water.
Explanation Factory setting
50-150% percent adjustment of
speed display
50-150% percent adjustment of
engine speed display
Engine speed warning at
1000-9900 rpm
Speed warning at
30-250 km/h (or mph)
0 = automatic adjustment
1 = darkest setting
2 = brightest setting
1 = km/h
2 = mph
1 = °C
2 = °F
Time in sec. after which the unit
switches off automatically (after
engine stop)
Troubleshooting
By purchasing this head up display, you have acquired a product that has been designed to the state of the
art and is operationally reliable. Nevertheless, problems or faults may occur.
Therefore, we would like to describe here how to eliminate possible faults:
Always follow the safety instructions!
No speed warning:
• The warning sounds are turned off.
• The set value for speed warning is not correct.
No engine speed warning:
• The warning sounds are turned off.
• The set value for engine speed warning is not correct.
The device does not switch on after starting the engine:
107
• The device is not switched on (on/off button (2) is in position OFF).
117 • The connection to the OBD diagnosis socket is disrupted.
The moving speed or engine speed does not correspond to the values in the vehicle dashboard:
50
• The wrong speed unit was set (km/h or mph).
• Incorrect setting value for display adjustment in the setup menu. Adjust the respective value in the setup
150
menu until the displayed values match.
Disposal
0
Electronic devices are recyclable waste materials and must not be disposed of in the household
waste.
1
Please dispose of the product, when it is no longer of use, according to the current statutory
requirements.
1
Technical Data
Operating voltage ..........................................12 V/DC (0-16 V/DC) of OBD diagnosis socket
10
Power consumption .......................................400 / 29 / 0.4 mA (max. / standby / off)
Connection cable ...........................................approx. 1.4 m
Dimensions (W x H x D) ................................91 x 53 x 12 mm
Weight ...........................................................40 g
Operating and storage conditions .................. -10 °C to +80 °C; 0% to 99% relative humidity (not
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represent the technical status at the time of printing.
Copyright 2016 by Conrad Electronic SE.
condensing)
1438345_V2_0616_01_m_en