Table des Matières
Publicité
Door Reversal
TOOLS REQUIRED
Phillips #2 screwdriver and a flathead screwdriver.
WARNING!
Excessive Weight Hazard
Use two or more people when moving the wine
cooler.
Door Removal
1. Unplug the wine cooler, empty all of its contents
and carefully lay the unit on its back.
2. Remove the adjustable foot located beside the
lower hinge assembly on the bottom right side
of the cabinet (see Fig. 1).
3. Unscrew the two retaining screws holding the
lower hinge assembly to the bottom of the
cabinet and set them aside (see Fig. 2).
4. Pull the door downward until it releases from
the top hinge pin (see Fig. 3), and then set the
door aside.
Door Reversal
5. Using a flathead screwdriver, transfer the top
hinge pin from the right side of the worktop to
the opposite (left) side of the worktop (see Fig.
3).
6. Transfer the plastic cap located on the top left
side of the door to the opposite (right) side of
the door (see Fig. 4).
7. Set the door onto the cabinet and push it
upwards until the top hinge pin is fully inserted
into the opening on the top left side of the door.
8. Remove the two retaining screws on the bottom
left side of the cabinet, and transfer them to
opposite (bottom right) side of the cabinet (see
Fig. 5).
9. Insert the bottom hinge pin on the lower hinge
assembly (see Fig. 2) into the opening on the
bottom left side of the door, and then align the
door and lower hinge assembly with the
cabinet.
10. Screw the lower hinge assembly (see Fig. 2) to
the bottom of the cabinet by aligning the holes
in the lower hinge assembly with the holes in
the bottom of the cabinet.
11. Reinstall the adjustable foot removed in step 1
(see Fig.1).
12. Ensure the door is squarely fitted to the cabinet
and that all fastenings are secure. Stand the
unit upright.
All manuals and user guides at all-guides.com
3
Top Hinge Pin
A
4
A
A. Plastic cap
A. Top hinge pin
Lower Hinge Assy.
A
B
C
D
E
A. Hinge washer
B. Bottom hinge pin
C. Screw washers
D. Screw gaskets
E. Screws
5
1
Adj. Foot
A
B
C
A. Screw washers
B. Screw gaskets
C. Screws
I M P O R TA N T !
Allow the unit to stand upright for at-least 1
hour before putting the unit into operation.
8
Características de su
Heladera para Vinos
1. Indicador y controles electrónicos : Para
ver la temperatura actual del heladera para
vinos y para graduarla.
2. Tablero de trabajo
3.
Puerta de vidrio templado: Polarización
para proteger contra radiación UV pero
permite ver fácilmente el interior.
4. Repisa para vino : Permite guardar hasta
5 botellas
de vino.
2
5.
Patas Niveladoras
6.
Juntas Magnéticas de la Puerta: Las
juntas ajustadas mantienen todo el poder
de enfriamiento y los niveles de humedad.
7. Luz interior (no se muestra): Luz interior
para iluminar su selección de vinos.
Instrucciones
para Nivelar
¡ AT E N C I Ó N !
Equipo muy pesado
Use 2 o más personas para
mover el heladera para vinos.
Instrucciones de Operación
1
6
Es importante que el enfriador
3. Gire las patas niveladoras
de vino quede nivelado: Para
en sentido horario para
nivelar el enfriador de vino:
levantar la unidad y
antihorario para bajarla.
1. Mueva la unidad a su
Vea la Fig. A.
emplazamiento definitivo.
2. Haga que una persona se
apoye suavemente sobre el
borde delantero de la
unidad para quitarle peso
subir
temporalmente a las patas
niveladoras.
Fig. A
29
2
3
4
5
bajar
Publicité
Chapitres
Table des Matières
