Publicité
Les langues disponibles
Les langues disponibles
Board camera
Item no. 1013266 CMOS 700TVL 6.35 mm (1/4")
Item no. 1013269 CMOS 700TVL 8.47 mm (1/3")
Item no. 1013270 Sony CCD 700TVL 8.47 mm (1/3")
Intended use
The board camera with manual focus adjustment is designed for surveillance and security purposes in
crucial, unsupervised areas (e.g. office spaces, intercom systems, gateways and parking garages). The
recordings can be played back on all playback devices with a video input e.g. a TV or monitor.
Operate the board camera with the protective housing intact and on 12 V/DC only. Avoid contact with
moisture at all costs!
For safety and approval purposes (CE), you must not rebuild and/or modify this product. If you use the
product for purposes other than those described above, the product may be damaged. In addition, improper
use can cause hazards such as short circuiting, fire, electric shock etc. Read the instructions carefully and
keep them. Make this product available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All company names and
product names are trademarks of their respective owners. All rights reserved.
Delivery content
• Board camera
• Cable with BNC & DC plug
• Operating instructions
Safety instructions
Read the operating instructions carefully and especially observe the safety information.
If you do not follow the safety instructions and information on proper handling in this
manual, we assume no liability for any resulting personal injury or damage to property.
Such cases will invalidate the warranty/guarantee.
a) Persons / Product
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may become dangerous
playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity,
moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and protect it from
any accidental use. Safe operation can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height can damage
the product.
• Also observe the safety and operating instructions of any other devices which are connected
to the product.
• Install the board camera in a suitable housing before use.
• It is not advisable to install the camera near strong magnetic or electric fields e.g. mobile
telephones, radio devices, electric motors, etc.
• Operate the board camera with a stabilized DC voltage power adaptor or rechargeable battery.
The power supply must supply sufficient current.
• After extreme temperature changes, the device requires 15 minutes to stabilize and adapt to
the new ambient temperature, before it can be used
• When connecting the camera, make sure the connection cable cannot be damaged by sharp
edges.
• Follow the operating instructions of any other devices or tools you use.
• If you use a power adaptor as a power supply, follow all applicable safety regulations at all
costs. Car chargers and power adaptors for toys are not suitable for use as a power supply and
when used result in damage to components or device malfunction.
• In industrial facilities, heed all applicable accident prevention regulations for electrical
installations and equipment.
b) Miscellaneous
• Consult an expert when in doubt about operation, safety or connection of the device.
• Maintenance, modifications and repairs are to be performed exclusively by an expert or at a
qualified shop.
• If you have questions which remain unanswered by these operating instructions, contact our
technical support service or other technical personnel.
Operation
Use a 12 V/DC power supply to operate the board camera. Do not use any other power
supply under any circumstances. The power supply must supply an output current of
100 mA. Avoid overloading the power supply at all costs.
Version 04/14
If you use a power adaptor as power supply, turn it off before connecting it.
Heed correct polarity when connecting. Failure to do so may result in damage to
components of the board camera.
Camera connections
Connect the board camera – depending on your version – as follows:
Item no. 1013266 - connect the connection cable's white plug to the + - V socket on the board camera
Item no. 1013269 - connect the connection cable's white plug to the + - V A socket on the board camera
Item no. 1013270 - connect the connection cable's 6-pin plug to the 6-pin socket,
The plug fits into the socket only if connected with correct polarity alignment.
Video connection
Connect the video input of your TV device or monitor to the connection cable's BNC socket.
Use a suitable optional BNC connection cable (polarity: video inlying, ground outlying).
Only use sufficiently shielded BNC cables as an extension, if needed. Use of other unsuitable
cables may result in malfunction.
The cable length should be kept as short as possible.
Electrical connection
Connect the power supply hollow socket on the camera connection cable to a suitable power adaptor. The
DC low-voltage plug must have the following features:
Dimensions: exterior 5.5 mm, interior 2.1 mm.
Polarity: inlying positive terminal (+), outlying negative terminal (-).
The board camera with SONY CCD 700TVL 8.47 mm (1/3"), item no. 1013270, features an
on-screen delay (OSD). A multipath switch for operating the on-screen display is located on
the connection cable. A description of the on-screen display is available in English from our
website, www.conrad.com.
Maintenance and cleaning
• The board camera requires no maintenance except occasionally cleaning the lens.
• Use a clean, lint-free, anti-static, dry cloth to clean the lens.
Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as they
can cause damage to the housing and malfunctioning.
Disposal
a) Product
Electronic devices are recyclable waste and must not be disposed of in the household waste.
At the end of its service life, dispose of the product according to the relevant statutory regulations.
You thus fulfil your statutory obligations and contribute to the protection of the environment.
Technical data
Item no.
Operating voltage
Current consumption
Image sensor
Light sensitivity
Exposure time
Number of pixels
Horizontal resolution
S/N ratio
Video output
Lens
Operating temperature
Cable length
Dimensions (W x H x D)
Weight
connect the connection cable's 3-pin plug to the 3-pin socket on the board camera.
1013266
1013269
12 V/DC
50 mA
6.35 mm (1/4")
8.47 mm (1/3")
CMOS colour
CMOS colour
0.01 lux / F1.2
1/25 - 1/15,000 s
720 x 576 PAL
720 x 576 PAL
700 TVL
700 TVL
≥52 dB
1.0Vp-p, 75 Ω
3.6 mm
-20 to +50 ºC
60 cm
38 x 32 x 38 mm
40 g
These operating instructions are published by Conrad Electronic SE, Klaus-Conrad-Str. 1,
D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.
© Copyright 2014 by Conrad Electronic SE.
1013270
8.47 mm (1/3")
Sony CCD colour
1/50 - 1/100,000 s
976 x 582 PAL
700 TVL
38 x 35 x 38 mm
V1_0414_02-HK
Publicité
