Maintenance And Inspection; Technical Data - EUCHNER CMS Serie Mode D'emploi

Operating Instructions
Read Heads/Actuators CMS for Safety Relay ESM

Maintenance and inspection

Remove iron swarf from the read head and actuator
at regular intervals.
Use only solvent‑free cleaning agents for cleaning
the actuators and read heads!
Regular inspection of the following is necessary
to ensure trouble‑free long‑term operation:
correct switching function
f
secure mounting of components
f
loose connections.
f
In the event of damage or wear and tear, the
damaged system component must be replaced.
Exclusion of liability under the
following circumstances:
incorrect use
f
non‑compliance with safety regulations
f
installation and electrical connection not per‑
f
formed by authorized personnel
failure to perform functional checks.
f
Service
If servicing is required, please contact:
EUCHNER GmbH + Co. KG
Kohlhammerstraße 16
70771 Leinfelden‑Echterdingen
Service telephone:
+49 711 7597‑500
E-mail:
support@euchner.de
Internet:
www.euchner.com

Technical data

Parameter Value
Read heads
Housing material Fiberglass reinforced PPS
Ambient temperature ‑20 ... +60 °C
Ambient temperature
‑20 ... +80 °C
CMS‑R‑BZD... only
Degree of protection IP67
Installation position Any, alignment with actuator
should be kept in mind (markings)
Connection Molded cable with cable end
sleeves/plug connector M8,
4‑pin/molded cable with plug
connector M12, 8‑pin
Switching voltage 35 V DC
Switching current I max. 0.1 A
e
Built‑in fuse 100 mA (per safety contact)
Rated conditional short‑circuit
100 A
current
1)
Contact status indication (only CMS‑R‑AZA)
Switching voltage 35 V DC
Switching current I max. 0.02 A
e
Monitoring contact (only CMS‑R‑BZD)
Switching voltage 35 V DC
Switching current I max. 0.1 A
e
Switching frequency f
max
5 Hz
at I 10 mA
1)
min
Switching frequency f
max
0.1 Hz
at nominal current 8 A 1)
Switching delay
26 ms
from state change
1) 2)
Method of operation Magnetic, reed contact
Mechanical life 100 x 10 operating cycles
6
Vibration resistance 10 ... 55 Hz, amplitude 1 mm
Shock resistance 30 g/ 11 ms
EMC compliance Acc. to EN 60947‑5‑3
Center offset m from actuator ± 2.5 mm at distance s = 3 mm
Switch‑on distance s
ao
See combination
Switch‑off distance s
ar
options table
Switching contacts
Classification acc. to EN 60947‑5‑3
CMS‑R‑BZB.../CMS‑R‑BZD...
CMS‑R‑AZA.../CMS‑R‑AZC...
Fusing of the power supply and the safety contacts
External contact fuse Fuse 10 A gG
1)
Actuator
Housing material Fiberglass reinforced PPS
Ambient temperature ‑20 ... +60 °C
Ambient temperature
‑20 ... +80 °C
CMS‑M‑BH only
Degree of protection IP67
Installation position Any, alignment with read head
should be kept in mind (markings)
Method of operation Magnetic
Vibration resistance 10 ... 55 Hz, amplitude 1 mm
Shock resistance 30 g/ 11 ms
Center offset m from read
± 2.5 mm at distance s = 3 mm
head
Switch‑on distance s
See combination
ao
options table
Switch‑off distance s
ar
Reliability values acc. to EN ISO 13849-1
Category 4
1)
Mission time 20 years
Performance Level e
1)
B 20 x 10 operating cycles
6
10D
1) Parameter dependent on the evaluation units ESM‑BA2.. and
ESM‑BA3..
2) Corresponds to the risk time according to EN 60947‑5‑3. This
is the maximum switch‑off delay for the safety outputs following
removal of the actuator.
5
Design CMS-.-A...
Y
Approach
direction
Z
Design CMS-.-B...
Y
Approach
direction
Figure 1: Alignment of read head and actuator
M3D36AS1
M3D88AS1
Alignment marking
X
Alignment marking
X
Z