Installing The Battery; Bluetooth Mode - Gear4 StreetParty Wireless 2 Manuel De L'utilisateur

• Stream music from any Bluetooth device*
• Removable and rechargeable lithium-ion
battery
• Speakerphone
• Up to 5 hours' battery life**
• Aux-in port for use with other music players
Register your StreetParty Wireless 2 to activate your warranty and receive product updates at
www.gear4.com/register
5
6
9
10
1 On/off button
2 Working indicator light (green)/charge
indicator light (red)
3 MIC
4 Bluetooth indicator light (blue)
5 Pause/Play
Instructions for use

Installing the battery

Open the battery compartment and place a
■
rechargeable battery into the base of the
speaker, following the polarity markings (
+/–). Guidelines for this are marked on the
base of the battery compartment.
Powering On
Slide the On/Off switch to the "ON" position,
■
the Blue LED will start to flash. The SPW2
will automatically enter Bluetooth mode when
powered on. If an Aux (3.5 mm) cable is
connected to the SPW2, the Blue LED will
not illuminate. Please note: When the SPW2
is in Aux-In mode the Bluetooth mode will be
disconnected.
Powering Off
Slide the On/Off switch to the "OFF" position,
■
all the LED status lights will shut off.

Bluetooth Mode

PAIRING
The unit will automatically go into "Pairing
■
Mode" when it is powered on. Go into your
devices settings menu and look for "GEAR4
SPW2". After the unit has paired, it will
connect automatically when the SPW2 is
powered on and the device is in range.
PLAYING MUSIC
Press to start playing music.
■
Press either "–" or "+" for volume control.
■
Copyright © 2014 Disruptive Hong Kong Limited. All rights reserved. Reproduction in part or in whole is
prohibited. GEAR4 and StreetParty Wireless 2 are trade marks of Disruptive Hong Kong Limited. iPhone and
iPod touch are trade marks of Apple Inc., registered in the U.S. and other countries. iPad is a trade mark of
Apple Inc. App Store is a service mark of Apple Inc.
The Bluetooth® word mark and logos are registered trademarks of Bluetooth SIG, Inc.
Disruptive Hong Kong declares that this portable speaker [PS013] is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/CE. It's possible for you to download a
complete copy of this declaration on the website www.gear4.com/DOC.
Please read before use.
• Micro-USB charging
• Soft touch finish
• Stereo sound
• Passive radiator for enhanced bass
*Bluetooth 3.0 (A2DP) range up to 10m, depending on line of sight.
**Battery life at maximum volume
6 Press for volume –
7 Press for volume +
8. Hands free answer / Hands free hang up
9. USB DC 5V
10. Aux-in
11. Battery cover
MAKING AND RECEIVING PHONE CALLS
When the SPW2 is connected and paired to
■
your device the SPW2 allows you to make or
receive phone calls with its built-in
microphone.
Press
■
To hang up a call press
■
To reject a call, press and hold the
■
Aux-In Mode
Plug in the supplied 3.5 mm cable into the
■
SPW2. The other end is connected to your
device.
Charging
Attach the USB cable to the SPW2, and plug
■
in to any USB charger. If the unit is
completely discharged, it will take
approximately 2.5 hours to fully charge. The
Red LED will illuminate during charging,
when it has completed it will turn Green.
LED Status
Bluetooth pairing Mode:
Green LED & flashing Blue LED
Bluetooth connected Mode:
Green LED & solid Blue LED
Aux Mode: Green LED only
Charging: Red LED
User Manual | StreetParty Wireless 2 | GEAR4 2
2
3
4
8
7
1
11
to accept a call.
.
.