Casals CCH32VCEK Mode D'emploi page 7

there Penetrating a water line causes property damage or may
cause an electric shock.
- Do not touch the bit during or immediately after operation.
The bit becomes very hot during operation and could cause
when serious burns.
- Do not use the power tool with a damaged cord. Do not
touch the damaged cord and pill the plug.
angled - Immediately unplug the plug from the main electricity in the
case that the cord gets damage and during maintenance.
use. Warning: Reduce the working time to avoid risks related
operly with too much vibration.
mables Description
y. (CCH32VCVEK, CCH40VCEK, CCH48VCEK)
direct A SDS Max Chuck
B Chuck sliding ring
y of a C Function Selector
D Handle
ch the E Auxiliary handle
F Depth Gauge
at the G Variable speed button
with a H Start-up switch
I Oil tank lid
orked (Only CCH32VCEK and CCH48VCEK)
ree to J Power indicator and carbon brush indicator
(Only CCH32VCEK and CCH48VCEK)
ds in a K Wing (Only CCH32VCEK)
efects
oblem Installation
Repair
Auxiliary Operation (CCH32VCEK)
stone, - Operate the appliance only with the auxiliary handle.
Wear - Turn the auxiliary handle (E) in counter clockwise direction
e with for adjustment.
- Set the auxiliary handle on the appliance into the required
position.
rvised - The depth can be set with the depth stop (F). Thereby
loosen the winged screw (K)
es. - Set de required drilling depth.
encing - Tighten the winged screw (K).
- Tighten the auxiliary handle (E) by turning it in clockwise
e work direction.
of the Auxiliary Operation (CCH40VCEK and CCH48VCEK)
- Operate the appliance only with the auxiliary handle.
duced
- Turn the auxiliary handle (E) in counter clockwise direction
on.
s are for adjustment.
ny for - Set the auxiliary handle on the appliance into the required
e and position.
osion. - The depth can be set with the depth stop (F).
- Set de required drilling depth.
- Tighten the auxiliary handle (E) by turning it in clockwise
direction.
Instructions for use
Before use:
- Make sure that all the product's packaging has been
removed.
- Prepare the appliance according to the function you wish
to use:
Fitting the working tools: (Fig. 2)
- Unplug the appliance from the mains.
- Only use tools with SDS-Max shaft.
- Clean and grease the shaft of the tool.
- Insert the tool by moving the sliding ring (B) back. Now the
SDS-Max chuck is open.
- Install the tool in. Turn it slightly until it can be pushed in all
the way and you can feel it engages into place.
- Release the sliding ring (B). Now the tool is locked.
Use:
- Connect the appliance to the mains.
- Select the appliance function desired.
Hammer drilling with rotation
- Turn the selector (C) until points to (
Chiseling (CCH32VCEK)
- Turn the selector (C) until points to ( ).
- To modify the position of the chisel turn the selector (C)
between position ( ) and ( ). Rotate the chisel until
the desired position and turn the selector (C) until points
to ( ).
Chiseling (CCH40VCEK)
- Turn the selector (C) until points to ( ).
- To modify the position of the chisel turn the selector (C)
until points to (O). Rotate the chisel until the desired position
and urn the selector (C) until points to ( ).
Chiseling (CCH48VCEK)
- Turn the selector (C) until points to ( ).
- To modify the position of the chisel turn the selector (C)
until points to ( ). Rotate the chisel until the desired
position and turn the selector (C) until points to ( ).
- Place the appliance against the surface you want to work.
- Press the appliance until the lengthways play is taken up.
- Turn the appliance on, by using the on/off button (H).
Note: Exerting high pressure does not increase machine
effectiveness!
).
7