Operating Information; Squeegee And Splash Guard Assembly, Disassembly And Adjustment; Squeegee Assembly; Squeegee Disassembly - GGM gastro BSW2200 Manuel D'instructions

between the mouth of the plug and the level of the
liquid.
To avoid risks, become familiar with the machine
movements, carrying out test runs on a large surface
without obstacles.
To obtain the best results in terms of cleaning and
equipment service life, you should do the following
simple but important operations:
- Identify the work area, moving all possible obstacles
out of the way; if the surface is very extensive, work in
contiguous and parallel rectangular areas.
- Choose a straight work trajectory and begin working
from the farthest area to avoid passing over areas that
have already been cleaned.

7 OPERATING INFORMATION

7.1 BATTERY CHARGING
Prepare and check the battery charge according to the
instructions provided in the specific section.
Detach the battery connector from the machine power
connector (the one with the gripping fins) and connect
the battery connector to the battery charger connector.
Do not connect the battery charger to the scrubber-
drier's main wiring connector.
Hold the connectors with the hands; do not pull them
using the cables.
If the machine is equipped with Pb-Acid batteries,
charge only in a well-ventilated area, lift the superior
cover (PHOTO A-1) and open the battery plugs.
Follow the steps indicated in the battery manufacturer's
operating and safety manual (see the battery
maintenance section).
If the machine is equipped with gel batteries
(maintenance free), follow the instructions indicated
here below.
If the machine is used regularly:
Always keep the batteries connected to the battery
charger when the machine is not being used.
If the machine is not used for extended time periods:
Charge the battery during the night after the last work
period, then disconnect the battery from the battery
charger.
Charge the battery during the night before using the
machine again.
Intermediate or incomplete charging while working
should be avoided.
If the machine is equipped with Pb-Acid batteries, use
a hydrometer to check the element liquid intensity on
a regular basis: if one or more elements are discharged
and the others fully charged, the battery has been
damaged and should be replaced or repaired (refer to
the battery service manual).
Close the element plugs and lower the superior cover.
Hold the connectors with the hands; don't pull them
using the cables.
Reconnect the machine connectors.
7.2 SQUEEGEE AND SPLASH GUARD ASSEMBLY,
DISASSEMBLY AND ADJUSTMENT
The squeegee is the main component that ensures
perfect drying.

7.2.1 SQUEEGEE ASSEMBLY

Lower the lifting system to avoid having to keep the
body raised while completing connections. (PHOTO B-
15)
Insert the two steel pivots placed on the squegee into
the special hoses situated on the squeegee support,
assuring the fixing with the provided safety pin. (PHOTO
D-40-45).
Firmly insert the tube into the hole in the body of
squeegee (PHOTO B-22)

7.2.2 SQUEEGEE DISASSEMBLY

Lower the lifting system to avoid having to keep the body
raised while completing connections. (PHOTO B-15)
Disconnect the suction hose from the squeegee body.
(PHOTO B-22)
Now free the floor cleaner from its housing (PHOTO
D-40-45)
7.2.3 SQUEEGEE STRAP ASSEMBLY
Position the front and rear metal strips, inserting the
securing screws in the relative holes. Put the front flap
(the one with the water slits) and the rear flap (the one
without water slits) in place, making sure they are
positioned correctly, and then tighten the securing
screws firmly.
7.2.4 SQUEEGEE STRAP DISASSEMBLY
Loosen and remove the retaining screws and bolts on
the squeegee body. Release the straps from the retaining
strips. (PHOTO D-42-43-44)

7.2.5 SQUEEGEE ADJUSTMENT

The pivot screw on the body (PHOTO D-39) adjust the
squeegee's slant with respect to the plane, according
to the machine's longitudinal axis. The two handles on
the sides, connected to the rear wheels of the squeegee
(PHOTO D-37-46) , are used to adjust the slant with
respect to the plane, according to the axis perpendicular
to the machine's operating direction.
To obtain a perfect adjustment, the rear strap (PHOTO
D-43), sliding as it moves, bends in all points, forming
an angle of 45° with the floor.
As the machine operates (advances), the knobs can
be used to adjust the slant of the straps: the slant
increases as the knob is screwed in and decreases as
it is unscrewed.
Squeegee drying must be uniform along the entire
drying line: damp patches mean that drying is insufficient;
turn the adjustment knobs to optimise drying.
7.2.6 SPLASH GUARD ASSEMBLY, DISASSEMBLY
AND ADJUSTMENT
The splash guard is equipped with an innovative comb
connection system. To lower or lift the splash guard off the
ground, just pull, detach the splash guard and then attach
it, by pressing it at the required level. (PHOTO A-7)
Use can also use a rubber mallet to insert it firmly into
position.

7.3 ACCESSORY ASSEMBLY, DISASSEMBLY AND

ADJUSTMENT (BRUSHES, SCRAPERS AND

ABRASIVE DISKS)

Never use the machine if brushes or scrapers and
31