AmerTac LPL601 Manuel Du Propriétaire

Owner's Manual
Location of Controls
1. 4 Super Bright LEDs
2. ON/OFF Switch with Selectable Dimmer
3. Folding Neck
4. Dual Adjustable Light Heads
5. Remote Control Signal Receiver
6. EZ Mount Bracket
7. Built-In Bubble Level
8. Battery Compartment*
9. Remote Control
10. Remote Control Signal Transmitter
11. Battery Compartment
12. ON/OFF Switch with Selectable Dimmer
*behind EZ Mount Bracket
Installation
EZ Mount Bracket
1. First remove printed paper mounting template from back of unit.
2. Drill two (2) pilot holes in the location where you want to mount the picture light. Place screws
(included) in pre-drilled holes. Tighten slightly until secure, but do not tighten all the way.
Slide EZ Mount Bracket keyhole slots over screw heads and into position.
3. Use the built-in bubble level to make sure the mounting bracket is level before securing it to the wall.
4. Once you confi rm that the bracket is level, tighten the screws to secure it to the wall. Take care to not over tighten.
5. 5. To hang the picture light on the mounting bracket, align the picture light with the mounting bracket and slide the unit down. Light will lock into position. To hang the picture light on the mounting bracket, align the picture light with the mounting bracket and slide the unit down. Light will lock into position.
6. To remove the picture light from the mounting bracket;
A) Hold the picture light by the base (not light head).
B) Slide the unit up.
C) Once the body releases from mounting bracket, pull the unit towards you.
Operating Directions
Light Positioning
Your wireless LED picture light ships fl at. To extend light head into proper position hold base in one hand and hold light head at center with other hand (where
neck attaches to light head). Rotate base backward until base and light head are at farthest point from each other. Pivot each light head independently to desired
angle.
NOTE: Each light head can only be turned 180° up or down (Fig 1). To prevent damage to the unit, do NOT overturn the light heads. Doing so may damage the
unit and will void the warranty.
YOU CAN OPERATE AND CONTROL THE WIRELESS PICTURE LIGHT TWO WAYS:
Manual Operation Using ON/OFF Switch On Light
• Press once for full brightness.
• Press and hold until the LEDs reach the desired brightness then release the button.
• Press a third time to turn the light OFF.
Remote Operation Using Wireless Remote Control
Where you mount the remote control in relation to the picture light will determine how is best to control the light using the remote control. The remote uses
InfraRed technology. This is the same type of technology used in most TV remote controls. As such, physically removing the remote from its mounting bracket
and pointing it at the picture light may be necessary. For best operation, use the remote control within 16 feet of the LED picture light.
1. Press the bottom of the switch once to turn the LED lights ON.
2. Press and hold the bottom of the switch until the desired level of brightness is reached then release the switch.
3. Press the bottom of the switch a third time to turn the LED lights OFF.
Positioning the Remote Control
For best operation, we recommend mounting the remote control with the
you mount your picture light, you may need to physically remove the Remote Control from it's bracket and point it directly at the Remote
Control Signal Receiver.
When doing so, the "Signal" graphic on Remote Control should be pointed in the direction of the Power Module.
Inserting/Replacing the Batteries
If the LEDs appear to be dim this is an indication that your batteries need to be replaced.
To Replace Batteries Once Mounted:
1. To remove the picture light from the mounting bracket;
A) Hold the picture light by the base (not light head).
B) Slide the unit up.
C) Once the body releases from mounting bracket, pull the unit towards you.
2. Open the battery compartment cover.
3. Remove old batteries and replace with 3 new AA batteries.
4. Make sure to follow battery polarity guide when installing new batteries.
5. Replace battery compartment cover and remount the light.
Changing the Remote Control Batteries
If the Remote Control does not work to turn the LED lights ON, this may be an indication that the battery needs to be replaced.
Replacing the Batteries:
1. Using a small phillips head, remove battery compartment cover on the back of the remote. As the screw is very small, take care
not to lose after removing. Remove battery compartment cover.
2. Remove the old battery (if replacing).
3. Insert new CR2025 battery. Be sure to match the battery polarity guide when installing new battery.
4. Replace the battery compartment cover and screw (making sure not to overtighten).
This product contains a Button battery. If swallowed, it could cause severe injury or death in just 2 hours.
Seek medical attention immediately.
Battery Precautions:
1. Use only the size and type of batteries specifi ed.
2. Always purchase the correct size and grade of battery most suitable for the intended use.
3. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment.
Reversed batteries may cause damage to the device.
4. Do not mix alkaline, standard (Carbon-Zinc), or rechargeable (Nickel Cadmium) batteries.
5. Replace all batteries of a set at the same time. Do not mix old and new batteries.
6. Clean the battery contacts and also those of the device prior to battery installation.
7. Do not dispose of batteries in fi re.
8. Remove batteries if consumed or if product is to be left unused for an extended period of time.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING: Modifi cations to this product not approved by the party responsible for compliance could void the user's
authority to operate the product.
Limited Warranty
Under normal use and conditions, provides to the original purchaser of this product a one year limited express
warranty that is set forth in the Limited Warranty stated in full. The Limited Warranty is in lieu of all other
express or implied warranties or liabilities subject to the exceptions explained fully in the Limited Warranty
on the website.
WIRELESS LED PICTURE LIGHT
11
graphic pointing upwards (Fig 2). Depending on where
REMOTE CONTROLLED
10
9
12
5
4
Unit Back
6
UNIT BACK
UNIT
Unit Slides Down
Onto Mounting Bracket
3
1 2
8
7
Mounting Bracket
Built-In
Bubble Level
Keyhole Slots
MOUNTING
SURFACE
Mounting Bracket
Screw
Picture Frame
Fig 1
Fig 2 Fig 2