Klein Tools KARBN 60345 Instructions page 2

ENGLISH
GENERAL SPECIFICATIONS
• Shell material: PC/ABS composite
• Surface pattern: Polymer Hydro-dipped film
• Standards: Klein Tools Karbn hard hats comply with Type I ANSI/
TM
ISEA Z89.1-2014, CSA Z94.1-15:
• Class E non-vented hard hats have been tested up to 20kV.
EN397:2012+A1:2012 (Clauses listed only):
• 5.2.4-Lateral Deformation (LD)
EN12492:2012 (Listed clauses only):
• 4.2.1.2-Front Energy Absorption Capacity
• 4.2.1.3-Side Energy Absorption Capacity
• 4.2.1.4-Rear Energy Absorption Capacity
TOP: Z89.1/Z94.1
FRONT:
EN12492
SIDES: EN12492
• Fits: Head Sizes 6-1/2 to 8 (20-1/2 to 25 inches / 52 to 64 cm)
SYMBOLS ON PRODUCT (FIG. A)
1
Reverse donning logo
2
Compliant Standards, Class, Type, and Head Size information
3
Recycling Code and material type
4 Date of manufacture
WARNING LABELS (FIG. B)
There are two warning labels affixed to the inside of this hard hat.
understand, and follow these instructions to ensure safe operation.
DO NOT REMOVE THESE LABELS.
WARNINGS
READ ALL INSTRUCTIONS. FAILURE TO FOLLOW THESE WARNINGS AND
INSTRUCTIONS MAY RESULT IN SERIOUS BODILY INJURY OR DEATH.
• This hard hat provides LIMITED protection from small objects striking
top, front, back, left and right sides of the hard hat. This is NOT an
ANSI/CSA Type II hard hat.
• DO NOT expose suspension and padding to open flame.
• ELECTRICAL WARNING: Avoid areas where the chance of electrical
shock exists. Non-vented versions meet Class E requirements by
providing limited electrical protection. Class C vented models provide
NO electrical protection.
• If the hard hat has sustained an impact, dispose of it IMMEDIATELY,
even if damage is not visible.
• NEVER alter, puncture, modify or engrave the shell or the suspension.
• DO NOT use paints, solvents, chemicals, adhesives, gasoline or like
substances on this hard hat – doing so can lessen the protection
offered against impact and penetration.
• DO NOT use this hard hat as a vehicular or recreational hard hat.
• DO NOT store objects between the suspension and the shell, as the
hard hat will not function as intended and can lessen the protection from
impact and penetration.
• Exposure to direct sunlight, corrosive environments, and/or extreme
temperatures below -40°F (-40°C) or above 120°F (49°C) can lessen
the ability of the hard hat to withstand impact and penetration.
MAINTENANCE
HARD HAT CLEANING AND STORAGE
• Clean the hard hat and suspension with mild soap and water only.
Rinse and wipe dry. Clean optional chin strap with damp cloth only.
Store in a cool place.
• See SWEATBAND AND TOP COMFORT PAD section of the operating
instructions (on other side) for additional maintenance information.
INSPECTION AND REPLACEMENT
Inspect the hard hat, including the suspension and shell, before and
after each use:
• Check the Hard Hat's shell for any cracks, breakage, discoloration,
chalky appearance, or any other damage, excessive wear or unusual
condition. These conditions may indicate reduced impact or penetration
resistance and the Hard Hat must be replaced IMMEDIATELY.
• The suspension and optional chin strap should be checked for cracks,
breaks, damaged stitching or any other damage, excessive wear or
unusual condition. If any of these conditions exist, the suspension
and optional chin strap must be replaced IMMEDIATELY.
• Always use genuine Klein Tools replacement parts. This product
works as a system, and use of unauthorized suspensions may
reduce the protection you receive from this hard hat.
SUSPENSION AND OPTIONAL CHIN STRAP: Must be replaced after no
more than 12 months of use.
ENTIRE HARD HAT: Entire Hard Hat must be replaced after no more
than 2 years of regular use, or 5 years from the date of manufacture,
whichever comes first.
These are MAXIMUM useful service life guidelines. Regular inspection
as detailed in the MAINTENANCE section above MUST be performed,
and may result in possible earlier replacement.
NOTE: This replacement schedule is a guideline that assumes
normal use and storage conditions for the hard hat. If the hard
hat is exposed to temperature extremes, persistent sunlight, or
chemicals, replacement may be required in a shorter time frame.
BACK: EN12492
ACCESSORIES AND REPLACEMENT PARTS
Klein Tools hard hat accessories and replacement parts are
available online or at major distributors:
DEFORMATION: EN397
• KHHSPN2: Premium Replacement Suspension
• KHHSWTBND2: Premium Sweatband (3-pack)
• KHHTOPPAD2: Premium Top Comfort Pad (3-pack)
• KHHSTRP: Chin Strap
• 56048: Rechargeable Auto-Off Headlamp (Spot/Flood/All-On)
• 56049: Rechargeable Light Array Headlamp (Flood only)
• 56062: Rechargeable Headlamp / Magnetic Work Light (Spot/Flood)
NOTE: KLEIN TOOLS CANNOT GUARANTEE THAT THIRD-PARTY
ACCESSORIES WILL PERFORM OR FIT OPTIMALLY WITH
KLEIN TOOLS HARD HATS.
Read,
450 Bond Street, Lincolnshire, IL 60069 1-800-553-4676
customerservice@kleintools.com
5
Universal accessory slots
6
Klein Tools accessory slots
Vents with shutter
7
(C-Class only)
8
Pivot adjustment
9
Size adjustment knob
10
Rear neck pad
Suspension strap
11
anchor slots
All hard hats come with suspension pre-installed at factory settings. The
suspension can be adjusted to ensure proper and secure fit to your head
for maximum protection. Follow the steps below:
STEP 1: Turn the size adjustment knob
the fit. Position the rear pad on the back of your head, closer to the neck.
Dress any bandanna knots or ponytails over the rear neck pad
STEP 2: Tighten by turning the size adjustment knob
until the hard hat is comfortable and snug. Move your head up,
down and side-to-side gently, like you would normally, and make
sure the hard hat stays on. Make sure that the hard hat is not
angled forward or backward, but rests level on your head.
If the hard hat does not fit properly at the factory settings, you
can further adjust the fit:
STEP 1: Free the suspension by turning the suspension bracket
approximately 90 degrees to free the bracket key
16
bracket key slots.
STEP 2: Determine which slot
the bracket slots deeper in the hard hat will move it higher on
the head and vice versa. Insert the bracket key
bracket
16
match the settings on the left and right sides to prevent the
suspension from sitting at an angle.
STEP 3: Verify the hard hat fits properly. Follow the steps in the
FITTING section to ensure proper fit. Ensure that accessories
you plan to use fit and function properly while maintaining the
hard hat's ability to perform its function optimally. Check with a
qualified safety expert, if unsure.
NOTE: The suspension strap lengths are xed and cannot be
adjusted. DO NOT attempt to alter.
USEFUL LIFE
WARRANTY
www.kleintools.com/warranty
DISPOSAL / RECYCLE
Do not place hard hat or its accessories in the trash. Items
must be properly disposed of in accordance with local
regulations. See www.epa.gov for additional information.
OPERATING INSTRUCTIONS
SEE OTHER SIDE.
CUSTOMER SERVICE
KLEIN TOOLS, INC.
www.kleintools.com
FEATURE DETAILS (FIG.C)
12
Washable sweatband
13
Washable top comfort pad
14
Suspension straps
15
Re ective stickers
16
Suspension bracket
17
Bracket key
18
Bracket key slots
FITTING (FIG. D)
counterclockwise to loosen
9
ADJUSTMENTS (FIG. E)
you want to reattach to. Using
18
17
approximately 90 degrees to lock into place. Always
SUSPENSION REPLACEMENT (FIG. F)
STEP 1: Place your forefinger under the strap anchor, and your
thumb over the anchor slot
enough force to release the anchor from the slot. Do this for all
anchor slots (4 total). NOTE: DO NOT pull on the suspension
straps to free the anchor. This could permanently damage the
straps, preventing them from performing as intended.
STEP 2: Make any height adjustments on the new suspension
before installation.
STEP 3: Push down each anchor until a click is heard and the
anchor cannot be pushed down any further. Do this for all 4
anchors. NOTE: DO NOT use sharp tools that may damage the
anchors, or pull on the straps to secure the anchors.
STEP 4: Check proper installation by pushing up on all 4 anchor
bases. The anchors should remain fully seated in their slots. If
not, repeat STEP 3.
STEP 5: Verify the hard hat fits properly. Follow the steps in
the FITTING section to ensure proper fit. Also ensure that
accessories you plan to use fit and function properly while
maintaining the hard hat's ability to perform optimally.
SWEATBAND AND TOP COMFORT PAD (FIG.H)
Klein Tools Karbn hard hats come with an advanced sweatband
TM
and top comfort pad made of evaporative material designed not
only to wick away sweat, but to also enhance cooling. Simply take
the sweatband or top pad and wet, shake to remove all excess
water and install for extended periods of cooling. Both are machine
washable in a normal wash cycle. Do NOT wash with bleach or
with detergents containing bleach. Machine dry on normal or low
heat setting only.
The sweatband and top comfort pad can be easily removed and
reinstalled on the suspension:
• The top comfort pad is held in place by a single hook-and-loop
pad .
27
• The sweatband is held in place by four suspension hooks
three hook-and-loop pads
simply detach all hook-and-loop pads and slide the sweatband
off the suspension hooks.
VENTS (C-CLASS ONLY)
Klein Tools Class C hard hats have vents and shutters on both
sides. The vents can be adjusted by simply sliding the shutter
tabs up or down.
7
The vents and shutters will NOT prevent vapors, liquids, or
debris smaller than the vents from entering the hard hat.
56048 HEADLAMP (FIG.G)
Klein Tools' 56048 Rechargeable Headlamp provides three
modes: 22-hour floodlight; 12-hour focused spotlight, 400
lumen All-On mode. 56048 features an LED battery gauge that
indicates remaining battery life, and an auto-off sensor that turns
off the headlamp in bright light or outdoors where additional
headlamp lighting is not needed, to extend battery life.
19
Release tab
20
On/Off/Mode button
21 Spot light
22 Flood lights
The 56048 can be attached to both the front or back of the hard hat via
the Klein Tools accessory slot. It can be tilted up to 64 degrees on the
hard hat and stand alone as a work light.
To install the headlamp onto a Klein hard hat, align the pivoting mount
.
10
with the Klein Tools accessory slot
24
push down until the headlamp clicks securely into place.
clockwise
9
To remove the headlamp, press forward on the Release Tab
and lift the headlamp out of the accessory slot.
REFLECTIVE STICKERS (FIG. C)
Klein Tools Karbn hard hats come with reflective stickers
TM
These have been tested and found compatible with this hard hat.
WARNING: Klein Tools DOES NOT approve the application of
stickers, hot stamps, inks, and foils that have metallic content
to this hard hat by end users. Such modi cations can alter the
from the
17
performance of the hard hat.
and turn the
. Push up with forefinger using
11
and
28
, on the side and front. To remove,
27
23
Bracket
24
Pivoting mount
25 Charging port cover
26 Light sensor
on the hard hat and
6
,
19
installed.
15