Technical Data - Conrad 75 41 09 Mode D'emploi

Pairing
☞
Before starting a pairing process, check that all of the cables have been connected correctly.
• Start the pairing menu, as described in the operating
instructions for the 2.4 GHz digital wireless DVR set
(order no. 752688).
Using this menu, the wireless camera is connected to
the wireless receiver.
• Use the "left" (" ") or right (" ") buttons on the the
DVR set's remote control to select a reception chan-
nel, and then press the "OK" button on the DVR set's
remote.
• You now have ca. 60 seconds to press the button "PAIR" (9) on the camera's connection cable. As soon as
the connection between camera and receiver has been created successfully, the image from the camera
is displayed on the monitor.
Information about the range
The range is a maximum of 200 m.
☞
This value, however, is the so-called "open space range" (the range the transmitter and receiver
are visible to each other, without disturbing infl uences).
In practical operation, however, there are walls, the ceilings of rooms etc. between the transmit-
ter and the receiver, which reduce the range accordingly.
Due to the different infl uences on the radio transmission, no specifi c range can be guaranteed.
However, trouble-free operation is usually possible in a detached house.
The range can sometimes be limited considerably by:
• Walls, reinforced concrete ceilings
• Coated / metallised insulating glass
• Proximity to metal & conducting objects (e.g., radiators, steel doors)
• Proximity to human bodies
• Broadband interferences, e.g. in residential areas (DECT telephones, mobile phones, radio-controlled
headphones, radio-controlled speakers, radio-controlled weather stations, baby monitors etc.)
• Proximity to electric motors, transformers, power-supply units, computers
• Proximity to badly shielded or uncovered computers in use or other electrical appliances
Troubleshooting
No camera picture on monitor
• Check whether the cable connections are correct.
• Select the correct input on the monitor.
• Check the power supply to the camera and DVR set.
• Carry out a pairing between the camera and the DVR set.
Interference lines in the image
• Reduce the distance between the camera and DVR set (but maintain a minimum distance of approx. 2-3 m).
• Point the antennae on the camera and DVR set in a different direction. Normally these should point verti-
cally upwards.
• Increase the distance to other electronic devices (i.e. other appliances that transmit at 2.4GHz, such as a
WLAN router).
Declaration of Conformity (DOC)
We, Conrad Electronic, Klaus-Conrad-Straße 1, D-92240 Hirschau, hereby declare that this product con-
forms to the fundamental requirements and the other relevant regulations of the directive 1999/5/EC.
☞
The Declaration of Conformity for this product can be found at www.conrad.com.
Maintenance and Care
• The product is maintenance-free. Repair or maintenance work must be carried out by a specialist.
• Clean the product with a soft, clean, dry cloth.
Do not use aggressive cleaning agents or chemical solutions, since these might damage the housing or
impair operation.
Do not apply too much pressure on the housing surface or the glass cover as this could cause scratch
marks.
Disposal
Dispose of the unserviceable product according to the relevant statutory regulations!

Technical Data

a) Camera
Operating voltage ........................5 V/DC
Power consumption .....................max. 550 mA (with activated IR LEDs)
Transmission frequency...............2.4 GHz
Transmission range .....................Max. 200 m (see chapter "Information on range")
Transmission channel ..................1 x AV
Protection class ...........................IP66
Operating temperature ................-10 to +50 °C
Coverage .....................................horizontal about 50°
IR range .......................................up to 8 m
Viewing fi eld with night use .........3 to 8 m
Microphone ..................................yes, built-in
Model ...........................................Colour:
Defi nition ......................................640 x 480 (VGA), 320 x 240 (QVGA)
Sensor .........................................6.35 mm, CMOS
Light sensitivity ............................1 to 8 lx
Dimensions ..................................approx. 103 x Ø 60 mm (without sunscreen, without antenna)
Weight .........................................approx. 258 g (without rain cover, without antenna)
b) Wall plug transformer
Operating voltage ........................100 - 240 V/AC, 50-60 Hz
Output ..........................................5 V/DC, 1 A
Installation/Operating Location ....Only in dry, enclosed indoor spaces
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1,
D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfi lming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.
© Copyright 2011 by Conrad Electronic SE.