MTD Yard Machines PS Manuel De L'opérateur page 4

For Parts Call 606-678-9623 or 606-561-4983 For Parts Call 606-678-9623 or 606-561-4983
• Do not operate a chain saw that is damaged, improperly
adjusted, or not completely and securely assembled. Be
sure that the saw's chain stops moving when the throttle
control trigger is released.
• Shut off the motor before setting the chain saw down.
• Use extreme caution when cutting small-sized brush and
saplings because slender material may catch the chain
saw and whip towards you or pull you off balance.
• When cutting a limb that is under tension, be alert for
springback so that you will not be struck when the ten-
sion in the wood fibers is released
• Do not cut through nails, rods in the tree, railroad ties or
pallets. Inspect a tree that you are going to cut for for-
eign objects that could cause injury or damage to your
chain saw.
• After striking a foreign object, stop the engine and thor-
oughly inspect for damage. Repair as necessary.
• Keep the handles dry, clean and free of the oil/fuel mix-
ture
• We do not recommend using the chain saw in a tree or
on a ladder.
• All chain saw service, other that the items listed in this
instruction manual maintenance instructions, should be
performed by competent chain saw service personnel.
• Use the right tool. Only use this chain saw for its intend-
ed purpose, to cut wood.
• Do not overreach. Always keep proper footing and bal-
ance.
• Always hold the unit with both hands when operating.
Keep a firm grip on all handles or grips.
• Never touch the chain or attempt to service the saw
while the engine is running. Make sure all moving parts
have stopped. Allow the chain saw to cool, as the chain
can be hot.
• Check the bar and chain at frequent intervals for proper
adjustment. Make sure the bar and chain are properly
tightened and sharpened. Visually inspect for damage.
Repair any damage before restarting or operating the
chain saw.
RULES FOR SAFE OPERATION
www.mymowerparts.com www.mymowerparts.com
KICKBACK SAFETY PRECAUTIONS
WARNING:
guide bar touches an object, or when the wood
closes in and pinches the saw chain in the cut.
Tip contact in some cases may cause a light-
ning-fast reverse reaction, kicking the guide bar
up and back towards the operator. Pinching the
saw chain along the top of the guide bar may
push the guide bar rapidly back toward the oper-
ator. Either of these reactions may cause you to
lose control of the saw, which could result in seri-
ous personal injury.
Do not rely exclusively upon the safety devices
built into your saw. As a chain saw user, you
should take several steps to keep your cutting
jobs free from accident or injury.
• With a basic understanding of kickback, you can reduce
or eliminate the element of surprise. Sudden surprise
contributes to accidents. Be alert to the potential for kick-
back at all times.
• Keep a good firm grip on the pole saw with both hands,
the right hand on the handle and the left hand confortably
on the pole lower when the motor is running. A firm grip
will help you reduce kickback and maintain control of the
saw. Don't let go.
• Make sure that the area in which you are cutting is free
from obstructions. Do not let the nose of the guide bar
contact a log, branch, fence, or any other obstruction
that could be hit while you are operating the saw.
• Always cut with the motor running at full speed. Fully
squeeze the throttle trigger and maintain a steady cutting
speed.
• Use only the correct original equipment manufacturer
replacement bars, chains and other parts and acces-
sories. These are available from your authorized service
dealer. Use of any unauthorized parts or accessories
could lead to serious injury to the user, or damage to the
unit, and will void your warranty.
• Follow the manufacturer's sharpening and maintenance
instructions for the saw chain.
• Use only the replacement guide bars and low kickback
chains specified for your saw to avoid injury.
3
KICKBACK may occur
when the nose or tip of the