Télécharger Imprimer la page
GE Versaflood II Signliter Instructions
GE Versaflood II Signliter Instructions

GE Versaflood II Signliter Instructions

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

g
GE
Lighting Solutions
READ THOROUGHLY BEFORE INSTALLING
WARNING
Risk of electric shock
• Turn power off before servicing
– see instructions
G E N E R A L
This luminaire is designed for use in outdoor
applications and should not be installed in areas of
limited ventilation or in high ambient temperature
enclosures. This fixture should be installed and main-
tained according to the following recommendations.
U N P A C K I N G
This luminaire has been packed so that no parts
should have been damaged during transit. Inspect to
confirm.
CAUTION
Unit will fall if not installed properly
• Follow installation instructions
INSTALLATION
CAUTION: For aimed-up application, remove
two screws from rear bottom corners of back
housing, and re-install them in front housing
rear bottom corners.
Luminaires Installed Without Conduit
(Standard mounting)
Type SO (AWG 14-3) cable (normally supplied by
user) is recommended for electrical connections to this
luminaire.
1. Unlatch, open door and remove door assembly.
Remove reflector and shield.
2.
Remove (4) knockouts in housing back. Using these
holes install housing to mounting surface with (4)
5/16 inch bolts, nuts and lock washers(*). Seal
around these bolts with appropriate sealing
compound(*).
*(Supplied by user.)
These instructions do not purport to cover all details or variations in equipment nor to provide for every possible contingency to be met in connection with installation, operation or
maintenance. Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser's purposes, the matter should be referred
to GE Lighting Solutions.
Versaflood
Figure 1
Figure 3
3. If the luminaire is prewired with power supply cable,
proceed to instruction 3a or 3b, otherwise remove the
wiring shield to expose the terminal board (see Figure
4). Loosen the cable strain relief clamp and insert the
supply cable through the gland from the back 7 to 9
inches. Connect cable leads to the terminal board,
retract cable to a good wire dress and tighten the
strain relief clamp. Refer to the WIRING section of
this instruction. Replace the wiring shield and
reflector and install lamp. Close and latch the lens
door.
GEH-5895
INSTRUCTIONS
II Signliter
®
Figure 2
Figure 4

Publicité

loading

Sommaire des Matières pour GE Versaflood II Signliter

  • Page 1 These instructions do not purport to cover all details or variations in equipment nor to provide for every possible contingency to be met in connection with installation, operation or maintenance. Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser’s purposes, the matter should be referred to GE Lighting Solutions.
  • Page 2 FINAL ASSEMBLY 3a. Pipe Mounted (See Figure 1) Mount the trunnion slipfitter on the support pipe CAUTION bracket and tighten all six set screws. Mount the luminaire and trunnion to the slipfitter using the 1/2-inch bolts and nuts provided. Level the luminaire. Risk of burn Drill a 5/16-inch diameter hole through the pipe •...
  • Page 3 Si vous souhaitez des informations complémentaires, ou si vous rencontrez un problème particulier qui ne soit pas adressé de votre point de vue d'acheteur, le sujet doit être remonté jusqu'à la société GE Lighting Solutions...
  • Page 4 4 3 5 3 3 GE Lighting Solutions is a subsidiary of the General Electric Company. Evolve and other trademarks belong to GE Lighting Solutions. The GE brand and logo are trademarks of the General Electric Company. © 2011 GE Lighting Solutions. Information provided is subject to change without notice. All values are design or typical values when measured under laboratory conditions.