Auroras ECLAIRAGE SOLAIRE A LED Manuel De L'utilisateur

User
Manual
Fix the two metal clips into position and attach to surface.
positioned approximately 20CM from each end of the Batten Light. Caution : Ensure correct anchor
sleeves are used for surface material. Plese see package contents before installation.
Insert Tensioning Bolt and attach the
Batten Light to the metal clips.
Connect the MC4 Connectors to the Solar
PV panel. Note : A matching pair of MC4
connectors are included in the contents of
this package. If the Solar PV Panel does
NOT have an identical pair of MC4
connectors, replace them with the ones
provided to guarantee a weather tight
connection.
MANUAL OF KEY FUNCTION
MAGIC
romote control is used to change the program
of the light. there are two sections , one is for setting
modes. the other is to change the time. This remote
controller are able to meet most of requirements for
different lighting situation. Light will work on"AUTO"
mode that will turn ON/OFF automatically uption day
and night as default setting. ON/OFF Key is to work at
day time with hand operation.
ON/OFF override button. 100% Light Output
Auto Function (Not Used). By Default Auto Function is programmed ON.
(Auto OFF During Day, Auto ON During Night)
Test Function. Light will operate for 20 seconds.
(The green indicator light will operate inside the end-cap if the battery is low / over-discharged.)
- Amount of Light output depends on the percentage selection.
- By default the light will operate for 12 Hours.
Constant light mode
* Helpful Hint.
Select a Time Setting (e.g. 4H) within 5 seconds to modify the default operating time.
Light Output 0%.
When sensor triggered - Light Output 100% for 1 minute.
Light Output 30%.
When sensor triggered - Light Output 100% for 1 minute
Light Output 50%.
When sensor triggered - Light Output 100% for 1 minute.
Light Output 100% (First 6 hours). Light Output 50% (Second 6 hours) - When sensor is triggered - Light Output 100% for 1 minute.
* Helpful Hint. Press "D" and a Time Setting (e.g.7H) = 100% for 3.5 hours then 50% for next 3.5 hours + 100% with sensor.
- Light Duration based on selection.
* Helpful Hint.
Time Setting mode
- Select 20% then 4H. Light will operate at 20% for 4 Hours.
- Select C then 8H. Light will operate at 50% for 8 Hours + 100% if sensor triggered.
- Select D then 3H. Operate at 100% for 1.5 Hours, 50% for 1.5 Hours + 100% with sensor.
5-6-7-8-9 are similar time function as 1-2-3-4....
20CM
20CM
1
It is recommended that each clip is
Using a screw driver, secure each clip onto the
Batten Light with the Tensioning bolt.
Note : This is only to secure the batten light so it
cannot be removed - Do not over tighten.
Power ON the Batten Light. A RED signal light can
be seen at the sensor end of the Batten Light.
Program the light to best suit your installation.
Please refer to setup guide of manual properly.
Light will work as 50% power when nobody there
and 100% power for 60mins when sensor is
Modes
Setting
Time
Setting
- By default the light will operate for 12 Hours.
* Helpful Hint.
Select a Time Setting (e.g. 9H) within 5 seconds
to modify the default operating time.
1
2
3
5
4
Assembly Mounting Bracket to Solar Panel
M6*16 Screws . This is to fix to solar panel
1
5
M6*16 Screws . Can fix in different holes for different mounting angle.
2 3
M8*16 Screws .
4
NOTICE
Please note the brackets for left and right sides are different, make sure it is
well-assembled properly.
GENERAL OPERATION
RED/GREEN/BLUE Status Light
* After turning the batten light ON. A Red/Green/Blue status light will cycle for two seconds then
stop. This
signals the batten light system is OK and will work
in the default operation of 0%+100% sensitivity powersurface material. Plese see package
contents before installation.
* After 1 minute of being ON a BLUE light will start to flash (slowly). This signalsthe BattenPRO is
now in a charge state and the solar panel is connected and operating as it should.
IMPORTANT:
If after 1 minute the BLUE light flashes (fast), check the polarity connection between the solar
panel and BattenPRO. "+ to +" and "- to -". And that a firm contact is made.
TESTING
To simulate the batten light operation during daylight hours. Disconnect or cover the Solar Panel
(This signals no voltage present to the batten light , and will simulate night operation) – Now turn
batten light ON. The Red/Green/Blue status lights will cycle for two seconds then stop. After 40
seconds, move in proximity of the micro wave sensor, once detected by the microwave sensor the
light will operate with 100% light output (default setting) then will turn off automatically after 30
seconds.
PLEASE NOTE:
The default setting is Mode A with 0% power (No Light Output) and 100% Light Output when a
person is in proximity. You can press buttons B , C or D or 20%/40%/80% to turn light ON
immediately to check light condition.
USING THE REMOTE
The remote uses microwave (IR) technology and needs to be used in the same way as a TV –You
must point the remote directly at the BattenPRO to send a command. After pressing a button on
the remote control, you will see a GREEN + BLUE light for two seconds. That signals a command
has been received successfully. Note : Refer to manual for remote control functions and
programming.
FAULT FINDING
BLUE LIGHT NOT VISIBLE / WORKING
• After doing steps under GENERAL OPERATION and the BLUE light is NOT giving any signal /
flashing. Double check the connection between the BattenPRO and solar panel is a firm connection
and polarity is correct.
• Meter the voltage from the solar panel to the MC4 connectors. Ensure the voltage is no less than
Finished assembly