Publicité
Les langues disponibles
Les langues disponibles
KEY-OVERRIDE-SL2
Copyright © 2006
-2007
, FORTIN AUTO RADIO INC
TOYOTA / LEXUS
1
1.A
1.B
PROGRAMMING
2
3
If the LED is flashing at this point the KEY-OVERRIDE-SL2 module is
already programmed and can't be programmed again. (To prevent
malicious use this module can be programmed in only one vehicle.)
4
5
If the LED turns ON, repeat from step 1.
LED Module Diagnostics :
On: Bypass Activated
OFF: Not activated
Flash: Not programmed.
WHAT IS DATA-LINK? / QU'EST-CE QUE LE DATA-LINK?
Starter
Alarm/
2 way
/module
Dem.
Data-Link
Alarme
dérivation
ALL RIGHTS RESERVED
Make the connections of the KEY-
OVERRIDE-SL2 to the vehicle:
Connector 1 (Black):
Determine the type of installation:
INSTALLATION WITH
DATA-LINK (See P.3)
INSTALLATION WITHOUT DATA-LINK (See
P.3)
Connector 2 (White):
Make the connections associated with the
vehicle in the VEHICLE FITGUIDE (P.1)
Keep programming button pressed while
inserting
connector 1
into the
KEY-OVERRIDE-SL2 module.
I
nsert
connector 2
into the
KEY-OVERRIDE-SL2 module.
Release the programming button when the
LED turns ON.
Insert one functional key into
the ignition barrel
(do not turn the key).
If the LED flashes 10 times,
the module is programmed.
Bypass
de
TOYOTA / LEXUS WITH SMART KEY
TOYOTA / LEXUS WITH SMART KEY
1
1.A
1.B
2
3
10'
4
5
If the LED is flashing at this point the KEY-OVERRIDE-SL2 module is already
programmed and can't be programmed again.
can be programmed in only one vehicle.)
6
Transpondor
7
8
If the LED turns ON, repeat from step 1.
The Data-Link is a connection between the remote-Starter/Alarm and the Bypass/Interface module.
eliminates all other connections between devices by using bidirectionnal communication.
connections thus reducing installation error, and eliminates the risk of theft.
installation time.
Le Data-Link est un connecteur entre le démarreur à distance/alarme et le module de contournent qui élimine tous les
branchements entre ceux-ci, par le biais d'une communication bidirectionnelle.
d'installation.
Il réduit les risques de vol.
INSTALLATION GUIDE
Made in Canada - Rev.S - 22 / 04 / 2008
W e b
s i t e :
h t t p : / / w w w . i f a r . c a
Make the connections of the KEY-
OVERRIDE-SL2 to the vehicle:
Connector 1 (Black):
Determine the type of installation:
INSTALLATION WITH
DATA-LINK (See P.3)
INSTALLATION WITHOUT DATA-LINK (See P.3)
Connector 2 (White):
Make the connections associated with the
vehicle in the VEHICLE FITGUIDE (P.1)
PROGRAMMING
Remove the battery from 1 factory
+
remote
Keep the other factory remotes away
from the vehicle (10 feet/3 meters
minimum).
Keep programming button pressed while
inserting
connector 1
KEY-OVERRIDE-SL2 module.
Insert
connector 2
KEY-OVERRIDE-SL2 module.
Release the programming button when the
LED turns ON.
(To prevent malicious use this module
Put the factory remote without the
battery close to the front of
ENGINE
START
STOP
START STOP
button as shown.
Factory key
fob
With the factory remote close to the start
button, press and hold the Start-Stop
ENGINE
button.
START
STOP
If the LED flashes 10 times,
the module is programmed.
It very easy to install and saves up 60% of the
Il diminue les branchements et les erreurs
Il est facile à installer et sauve jusqu'à 60% du temps à l'installation.
into the
into the
ENGINE
This connection
It reduces the number of
P.5
Publicité
