Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
O P E R A T I N G I N S T R U C T I O N S
Radio controlled door/
window detector
Item-No. 75 13 77
1. Intended Use
The radio controlled door/window detector disposes of a magnetic contact, its activation being
reported to the radio controlled alarm control unit.
The power supply takes place by means of a 3V button cell (type CR2032). Mounting and oper-
ating the radio controlled door/window detector is only permitted in dry indoor locations. The
product must not get damp or wet!
Any use other than that described above could lead to damage to this product and involves the
risk of short circuits, fire, electric shock, etc.
No part of the product should be modified or reassembled. It is not authorized to use the device
if the housing is not completely closed.
All safety and assembly instructions must be observed without fail!
2. Contents
• Radio controlled door/window detector
• Magnet
• Assembly material
• Operating instructions
3. Explanation of Symbols
The flash icon in a triangle is used to alert you to potential personal injury hazards
such as electric shock.
A triangle containing an exclamation mark indicates important information in these
operating instructions which are to be observed without fail.
The "hand" symbol indicates special information and advice on operating the
device.
4. Safety instructions
The warranty will be void in the event of damage caused by failure to observe
these safety instructions!
Liability for any and all consequential damage is excluded!
We shall not accept liability for damage to property or personal injury caused
by incorrect handling or non-compliance with the safety instructions. The
warranty is voided in these cases.
Dear Customer, the following safety instructions are intended not only for the protection
of your health but also for the protection of the device. Please read carefully through the
following points:
a) General information
• If you are not sure when assembling, connecting and installing the device or if you have doubts
as of the mode of operation, do not effect the assembly/connection/installation yourself, but
rather contact a specialist.
• The unauthorised conversion and/or modification of the product is inadmissible because of
safety and approval reasons (CE).
• The product is intended for mounting and operating in dry, closed indoor locations only. The
product must not get damp or wet.
• Keep the product out of the reach of children.
• Do not leave the packaging material lying around carelessly since it constitutes a hazard to chil-
dren.
• Handle the product with care. It can be damaged through impact, blows, or accidental drops,
even from a low height.
b) Batteries and rechargeable batteries
• Batteries and rechargeable batteries must be kept out of the reach of children.
• Please observe the correct polarity, when inserting batteries/rechargeable batteries into
the unit.
• Do not leave batteries/rechargeable batteries lying about openly. There is a risk that they may
be swallowed by children or pets. If swallowed, consult a doctor immediately.
• Leaking or damaged (rechargeable) batteries in contact with the skin might cause acid burns,
therefore, use suitable protective gloves.
• Make sure that batteries/rechargeable batteries are not short-circuited or thrown into fire. There
is a risk of explosion!
• Never disassemble batteries/rechargeable batteries.
• Conventional batteries may not be recharged.. There is a risk of explosion!
• In case of longer periods of non-use (e.g. during storage) remove the inserted
batteries/rechargeable batteries to avoid damage by a leaking battery.
5. Assembly
www.conrad.com
Version 04/09
°
Tip:
Test the correct function first before screw assembling, to avoid unsightly „false" holes.
• The radio controlled door/window detector consists of two
components, the magnet (the smaller component) and the
radio controlled door/window detector (the larger compo-
nent).
Basically the radio controlled door/window detector is moun-
ted on the door frame (or e.g. window frame) and the mag-
net on the door (or e.g. window).
• Make absolutely sure the bottom of the magnet is 8 mm
away from the bottom of the radio controlled door/window -
detector.
A higher or lower mounting reduces the range of the magnet,
the magnet must be mounted closer to the radio controlled
door/window detector!
The horizontal distance from the magnet to the radio con-
trolled door/window detector must be a maximum of 20 mm.
Ideal is a distance of approx. 10-15 mm.
To guarantee a better hold of the radio controlled door/win-
dow detector, we advise you, to use the mounting plate (A;-
see picture right) included in delivery.
• Apply the mounting plate (A) to the contemplated mounting
site and mark both drill-holes.
• Attach the mounting plate (A) with appropriate mounting
material.
• Stick the two-sided adhesive tape (B) included in delivery
onto the mounting plate (A).
• Attach the radio controlled door/window detector (C).
• Now attach the magnet (pay attention to the distances!) by
means of the double-sided adhesive tape included in
delivery.
6. Programming the radio controlled door/window detector
in the radio controlled alarm device.
Please also observe the instructions of your radio controlled alarm device when programming
the radio controlled door/window detector.
You hereby get a general idea of the possible alarm zones the radio controlled door/window
detector can be programmed for.
To program the radio controlled door/window detector in the radio controlled alarm device,
please act as follows:
Step
1
2
3
4
5
Please note that the radio controlled door/window detector disposes of a
magnetic sensor (Reed-contact) on the left hand side. This side of the radio
controlled door/window detector is additionally marked with a red line.
Therefore the mounting of the magnet included in delivery can only take place
on the left side of the radio controlled door/window detector.
Be careful when drilling that you do not damage any power, gas or water
lines, danger to life!
Action
Function
Push the button
„PROG" on your radio
controlled alarm device.
Introduce
You access the
four-digit
programming mode.
the master code.
Push the
You access the
button 3 on the
programming mode for
alarm device.
Programming new sensors. the „Zone Status LEDs"
Press the key
1, 2, 3, 4, 5, 6, 7, 8, 9
or 0, depending on
which memory
you would like
to use
Then activate
A voice message
Radio controlled door/
confirmed by the
window detector.
successful programming.
A
B
C
Note
3 x short bleeps to the
Alarm device confirms
the correct code input. 1 x
long bleep indicates an
incorrect code input.
As soon as you access
programming mode
on the alarm device light up
or blink.
** see explanation in the fol-
lowing chart
To select the
right memory,
please observe the
above chart.
The settings are
saved and the
programming mode is exit-
ed.
Publicité
Table des Matières
