Technical Data; Warnings Regarding Installation - Niko 100-78200 Mode D'emploi

XXX-78200
Changing a switching command
Step Action
1 Press for three seconds.
2 Press briefly...
3
Press briefly...
4
Press or .
5
Press briefly...
6
Press .
Deleting a switching command
Step Action
1
Press for three seconds.
2
Press briefly...
3
Press and simultaneously.
4
Press .
3.3. Reset
You delete all of the entered programs and settings. The time switch is returned to the factory settings.
Step Action
1
Press and hold and press
briefly.
2
Press or .
3
Press .
4. OPERATION AND USE
A. Manual mode
The switch position can be manually changed temporarily at any time, even while an automatic program
(automatic mode) is running.
Step Action
1
Press briefly.
2 Press briefly.
A flashing C1/C2 with the hand symbol (
relative to the program. This position is temporary. The time switch is now in manual mode.
At the next change planned for the program, the automatic mode will be reactivated. The automatically activated
switch position is indicated by a clock ( ) next to the channel/channels.
EN nv Niko sa
Result
You enter the programming mode.
The first switching command (01) appears.
... until you have selected the switching command to
be changed.
... until the desired week block or day appears. In
sequence:
- 1234567 = entire week (Monday through Sunday)
- 123456 = long work week (Monday through Saturday)
- 12345 = short work week (Monday through Friday)
- 567 = long weekend (Friday through Sunday)
- 67 = short weekend (Saturday and Sunday)
- 1 = Monday, 2 = Tuesday (individual days)
You set the hour at which the action must be
performed:
press briefly: set per minute
•
press and hold: set per five minutes and then
•
per hour
... until the desired switch position of the channel/
channels appear. In sequence:
C1 C2
OFF OFF
ON OFF
OFF ON
ON ON
OFF -
ON -
- OFF
- ON
You return to the start screen.
Result
You enter the programming mode.
The first switching command (01) appears.
... until you have selected the switching command
to be deleted.
The content of the selected memory location is
deleted.
You return to the start screen.
Result
All programs and settings are deleted.
The channel-setting mode is activated.
You set the number of channels.
Your selection is confirmed.
You return to the start screen.
Result
You change the switch position of channel 1.
You change the switch position of channel 2.
) indicates that you have manually adjusted the relevant channel
Industriepark West 40, BE-9100 Sint-Niklaas, Belgium — tel. +32 3 778 90 00 — fax +32 3 777 71 20 — e-mail: support@niko.eu — www.niko.eu
B. Permanent mode
for exactly three seconds to deactivate the automatic mode and to permanently
Press and hold or
activate the manually selected switch position of the channel/channels. The programmed switching times do
not change the switch position. The time switch is now in permanent mode: C1/C2 with hand symbol (
is not flashing but is illuminated permanently.
If you press and hold or , you run through the various modes in the following sequence:
permanent mode on
•
permanent mode off
•
automatic mode on
•
permanent mode on
•
...
•
Press or briefly to deactivate the permanent mode and to return to the manual mode.
C. Functions with an external push button
You can also control the sensor from various locations.
You can connect one or two external push buttons to the actuator between L and E1 and E2, respectively:
• The contact between L and E1 has the same function as
The contact between L and E2 has the same function as
•
D. In combination with Nikobus
When adding or programming all of the other Nikobus functions, you must remove all sensors from the actuators.
Before programming the sensor, you place the sensor on the actuator and you can manually control channels 1
and 2 so that a switching command is sent on the Nikobus.
5. TROUBLESHOOTING
In the event of malfunctions, press briefly.
The time switch restarts. The settings are saved.

6. TECHNICAL DATA

number of switching commands
min. switching time
operational reserve (available after 12 hours of operation)
flush-mounting height
ambient temperature
storage temperature

7. WARNINGS REGARDING INSTALLATION

- The installation should be carried out by a registered installer and in compliance with the statutory regulations.
- This manual should be presented to the user. It should be included in the electrical installation file, and it
should be passed on to any new owners. Additional copies are available on the Niko website or via the Niko
support service. The latest manual for this product is available on the Niko website at any time.
- During installation, the following should be taken into account (non-exhaustive list):
- the statutory laws, standards and regulations.
- the technology currently available at the time of installation.
- this manual, which only states general regulations and should therefore be read within the scope of each
specific installation.
- the rules of proper workmanship.
This product complies with all of the relevant European guidelines and regulations. If applicable, you can find
the EC declaration of conformity regarding this product at www.niko.eu.
8. NIKO SUPPORT
In case of doubt or for the specific exchange procedure in case of a possible defect, contact the Niko support
service in Belgium at +32 3 778 90 80 or your wholesaler/installer. Contact details and more information can
be found at www.niko.eu under the "Help and advice" section.
9. GUARANTEE PROVISIONS
- The period of guarantee is four years from the date of delivery. The delivery date is the invoice date of purchase
of the product by the consumer. If there is no invoice, the date of production applies.
- The consumer is obliged to inform Niko in writing about the non-conformity, within two months after stating
the defect.
- In case of a non-conformity, the consumer only has the right to a product repair or replacement free of
charge, which shall be decided by Niko.
- Niko shall not be held liable for a defect or damage resulting from incorrect installation, improper or careless
use, incorrect operation, transformation of the product, maintenance that does not adhere to the maintenance
instructions or an external cause, such as damage due to moisture or overvoltage.
- The compulsory regulations of the national legislation concerning the sale of consumer goods and the
protection of the consumer in the countries where Niko sells, directly or via sister companies, subsidiaries,
chain stores, distributors, agents or permanent sales representatives, take priority over the above-mentioned
rules and regulations.
.
.
max. 24
1 minute
clock will continue to work for 30 more minutes
0.8 – 1.5 m
0 – 40°C
-25 – 75°C
PMXXX-78200R17405
)