Casals CCH26REAK Notice Originale page 4

tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users
-Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool's
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools
-Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control
-Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
different from those intended could result in a hazardous
situation.
Service
-Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained
-Any misuse or failure to follow the instructions for use
renders the guarantee and the manufacturer's liability null
and void.
Hammer safety warnings
- Wear ear protectors. Exposure to noise can cause
hearing loss.
- Use auxiliary handle(s), if supplied with the tool. Loss
of control can cause personal injury.
- Hold power tool by the insulated gripping surfaces
when performing an operation where the cutting
accessory may contact hidden wiring or its own cord.
Cutting accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and could give
the operator an electric shock
Additional safety warnings
- CAUTION: In order to prevent overheating do not cover
the appliance.
- Ensure that neither the air access nor exit become
either totally or partially covered by drapery, clothing, etc.,
as this increases the risk of fire.
- As an additional protection to the electrical supply for
the appliance, it is advisable to have a differential current
device with a maximum sensitivity of 30 mA. Ask for
advice from a competent installer.
- Do not use the appliance if the cable or plug is damaged.
- Ensure that the voltage indicated on the rating label
matches the mains voltage before plugging in the
appliance.
4
- If any of the appliance casings breaks, immediately
disconnect the appliance from the mains to prevent the
possibility of an electric shock.
- Do not use the appliance if it has fallen on the floor, if
there are visible signs of damage or if it has a leak.
- CAUTION: Maintain the appliance dry.
- CAUTION: Do not use the appliance near water.
- Do not use the appliance with damp hands or feet, or
when barefooted.
- Do not wrap the power cord around the appliance.
- Do not clip or crease the power cord.
- Check the state of the power cord. Damaged or tangled
cables increase the risk of electric shock.
- Do not touch the plug with wet hands.
- Fully unroll the appliance's power cable before each use.
- Do not use the appliance if its accessories are not
properly fitted.
- Do not use the appliance if the accessories or
consumables attached to it are defective. Replace them
immediately.
- Use the appliance handle/s, to catch it or move it.
- Keep the appliance in a dry, dust-free place, out of direct
sunlight.
- Do not use the appliance on any part of the body of a
person or animal.
- If the application tool should become blocked, switch the
machine off. Loosen the application tool.
- Before switching on the power tool, make sure that the
application tool moves freely. When switching on with a
blocked drilling tool, high torque reaction can occur.
- Use clamps or a vise to secure the object to be worked
in place. The work will be safer if both hands are free to
control the tool.
- Let the appliance running with no load for 30 seconds
in a safe position. If you notice serious vibration or other
defects stop the appliance immediately. Then check the
problem and /or proceed as we describe on Anomalies and
Repair clause.
- Use personal protective equipment. Always wear dust
mask
- When working in amianthus/asbestos and/or silica
stone, the dust produced is extremely harmful to your
health. Wear protection against inhalation of this dust,
in compliance with current regulations on accident
prevention.
- This appliance is for professional use.
- This appliance is not a toy. Children should be supervised
to ensure that they do not play with the appliance.
- Do not expose the appliance to extreme temperatures.
- Check the position of power cables before commencing
work ensuring they are well away from the work area.
- Keep hands and other body parts well away from the
work area whist the tool is in use.
Produ
Descr
A
B
C
D
E
F
G
H
I
J
K
L
M
Instal
Auxili
- Ope
- Turn
adjust
- Set t
positio
- Tigh
directi
- The
press
- Rele
Befor
- Mak
remov
- Prep
wish t
Fittin
- Unp
- Only
- Clea
- Insta
drill bi
can fe
- Ensu
SDS-p
- Unpl
- Fit th
descri