Publicité
Les langues disponibles
Les langues disponibles
c) Connection
When connecting an HDMI display to the LOOPOUT socket (6), make sure the HDMI cable
connects to "input 1" socket on the HDMI display.
The transmission distance may vary depending on cable quality and type.
The cable should not be tangled or rolled to avoid crosstalk or signal interference.
•
Disconnect all devices from the power supply, then connect all peripherals to the transmitter as indicated
in the connection diagram.
•
Use an HDMI cable to connect a source device to the HDMI IN socket (5).
•
Use an HDMI cable to an HDMI display via the LOOPOUT socket (6).
Use a Cat5e cable to connect to the receivers (14) via the OUTPUT ports (1), (2), (3), and (4).
•
•
Connect the receivers (14) to an HDMI display.
•
Turn the transmitter power on by connecting one end of the power adaptor to the DC 12V input (8), and
the other end to a power outlet.
•
Turn on the power on to connected devices.
Description of Controls
Control
Function
OUTPUT 1-4
Connects to remote receivers (14) using Cat5e (or higher) cables.
LOOPOUT
Connects to an HDMI display via HDMI cable.
Connects to an RS232 control device e.g. laptop computer to control the
CONSOLE
transmitter or to update the firmware. Cable (not included) See section "R232
Console Socket a) Settings".
DC 12 V
Connection for power supply
ON LED
Indicates the unit is receiving power.
HDMI IN LED
Lights up when there is an active connection to a HDMI device in the input.
LOOPOUT LED
Lights up when there is an active connection to a HDMI device in the output.
SELECT EDID
See section "EDID b) Custom EDID Settings".
SET EDID
See section "EDID b) Custom EDID Settings".
R232 Console Socket
The RS232 (9) socket allows you to connect a PC or notebook and issue commands for example, turning on
or off from a compatible projector or monitor.
a) Settings
Hyper Terminal setting: 57600bps (8 N 1)
Pin
Function
CONSOLE
CONSOLE
2
TX
3
RX
5
GND
b) Command List
Command
Description
OUTPUT 1 OFF
OFF 1(Enter)
OFF 2(Enter)
OUTPUT 2 OFF
OFF 3(Enter)
OUTPUT 3 OFF
OFF 4(Enter)
OUTPUT 4 OFF
OFF 5(Enter)
HDMI LOOPOUT OFF
EDID
EDID (extended display identification data) is a data structure that is used between the display and source
device. The data from the source device is used to deliver the correct video resolution and audio format to
the output device (monitor).
Setting
EDID
0
Custom EDID 1
1
Custom EDID 2
2
1024 x 768
3
1280 x 720
4
1280 x 1024
5
1366 x 768
6
1600 x 900
7
1680 x 1050
a) Settings
•
Determine which setting is applicable to your output device.
•
Use a small flat-tip screwdriver to SELECT (12) an EDID setting.
•
Press the SET button (13).The HDMI IN (10) and LOOPOUT (11) LED indicators
will flash.
•
When the transmitter restarts, the new EDID settings will be set.
Command
Description
ON 1(Enter)
OUTPUT 1 ON
ON 2(Enter)
OUTPUT 2 ON
ON 3(Enter)
OUTPUT 3 ON
ON 4(Enter)
OUTPUT 4 ON
ON 5(Enter)
HDMI LOOPOUT ON
Setting
EDID
8
1920 x 1080
9
1920 x 1200
A
720p 50Hz LPCM 2 CH
B
720p 60Hz LPCM 2 CH
C
1080p 50Hz LPCM 2 CH
D
1080p 60Hz LPCM 2 CH
E
1080p 50Hz MULTI
F
1080p 60Hz MULTI
SELECT
SELECT
8
b) Custom EDID Setting
If the required display settings are not shown in the EDID settings table, you can automatically detect the
HDMI display resolution and create a custom EDID setting.
•
The transmitter should be connected to the power supply.
Use a small flat-tip screwdriver to SELECT (12) a custom EDID setting 1 or 2.
•
•
Connect to an HDMI display using an HDMI cable to the LOOPOUT socket (6) on your receiver. The
display should be connected to the power supply and turn on.
•
Press and hold the SET button (13) for approximately 3 seconds until the HDMI IN (10) and
LOOPOUT (11) LED indicators flash slowly then quickly.
•
When the transmitter restarts, the new EDID settings will be set.
Custom EDID settings will not be lost if the transmitter is disconnected from the power supply.
Repeat the above steps to overwrite custom settings.
Care and Cleaning
•
Disconnect the product from the mains before each cleaning.
•
Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as they can
cause damage to the housing and malfunctioning.
•
Clean the product with a dry, fibre-free cloth.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the household waste.
At the end of its service life, dispose of the product in accordance with applicable regulatory
guidelines. You thus fulfill your statutory obligations and contribute to the protection of the
environment.
Technical Data
a) Transmitter
Input voltage / current ........................... 12 V/DC, 1 A
Power consumption .............................. max 9.6 W
Interface ................................................ HDMI IN: 1x HDMI type A (1.4 compliance)
LOOPOUT: 1x HDMI type A (supports CEC)
OUTPUT: 4x RJ45
Resolution ............................................. max 1080p (at 60 Hz)
Transmission distance .......................... Cable type Cat5e
approx. 40 m at 1080p
approx. 70 m at 720p
RS232 ................................................... Interface: DB9(F)
Baud rate 57600 bps
Cable support ...................................... Cat5e or above recommended
Supports ............................................... AC3, DTS, Dobly TrueHD, DTS HD
RS232 control
EDID management
Operating conditions ............................. 0 to +70 ºC, <95 % RH (non-condensing)
Storage conditions ................................ -20 to +85 ºC, <95 % RH (non-condensing)
Dimensions (W x H x D) ....................... 40 x 101 x 167 mm
Weight .................................................. 460 g
b) Receiver
Resolution ............................................. max 1080p (at 60 Hz)
LED Indicators ...................................... Yellow (reserve), Green (powered on)
Connectors ........................................... Input: RJ45
Output: HDMI type A
Operating conditions ............................. 0 to +55 ºC, <95 % RH (non-condensing)
Storage conditions ................................ -20 to +85 ºC, <95 % RH (non-condensing)
Dimensions (W x H x D) ....................... 20.2 x 24 x 57.5 mm
Weight .................................................. 20 g (each)
c) Power Adaptor
Input voltage / current ........................... 100 - 240 V/AC 50/60 Hz, 0.5 A
Output voltage / current ........................ 12 V/DC, 1 A
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights
including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication
represents the technical status at the time of printing.
Copyright 2019 by Conrad Electronic SE.
*2176714_v2_1219_02_dh_m_en
Publicité
