Télécharger Imprimer la page

Princeton Tec REMIX RGB Notice D'utilisation Et D'entretien

Publicité

Liens rapides

English
Battery Installation –
See Battery Installation Diagram
• 3 AAA
• Alkaline (LR03)
• Rechargeable NiCad or NiMH
Princeton Tec cares about the environment and
recommends recycling batteries. For more information
about battery recycling, please go to:
www.batteryrecycling.com
To install the batteries, unlatch the battery door.
Open the Remix case by popping the door latch
over the catch and rotate the door open.
Install three AAA batteries according to the polarity
markings on the inside of the cabinet. Observe
proper battery polarity when installing the batteries.
Improper installation of the batteries will damage the
light and void the warranty.
Rotate the door to the closed position, squeeze the
body between your forefingers and thumb to snap the
door latch over the catch.
WARNING
!
• Never mix fresh and used batteries.
• Never mix different battery brands or
chemistry types.
• Always remove drained batteries immediately.
• Remove batteries during long periods of storage.
NOTE: Rechargeable NiCad or NiMH batteries
may result in reduced brightness due to lower
nominal voltage.
Switch Operation –
See Switch Operation diagram
The Remix has two light sources to choose from: three
Ultrabright LEDs and one Maxbright LED. The
Ultrabright LEDs have one level in each of three color
modes: red, green and blue. The white Maxbright LED
has two modes (Low and High).
The first press will turn the light on in red mode. A
subsequent press within 1.6 seconds changes to
green, and another press within 1.6 seconds
changes to blue. To activate the Maxbright LED,
press and hold the button down until the light turns
on in low mode. Another press within 1.6 seconds
will change to high level.
NOTE: If you keep the button pressed the light will
continue to switch back and forth between the 5mm
and Maxbright LED until you release the button.
Any button press after two seconds will turn the light off.
One final note about the light function – If you have the
light turned on, (and more than 1.6 seconds has
passed since your last button press) and you press
and hold the button down to switch light sources, you
will be in darkness for about one second as the light
Figure 1 – Switch Operation
press 1x = Low
press 2x = High
1 MAXBRIGHT
To switch between light
sources, press and hold
press 1x = Red
button (1-2 seconds)
press 2x = Green
press 3x = Blue
3 ULTRABRIGHT
* Princeton Tec calculates total burn time as the time it takes for the light source to produce a
minimum of 0.25 lux at 2 meters. 0.25 lux is about the equivalent of a full moon on a clear night.
* Princeton Tec définit la durée totale d'éclairage comme le temps nécessaire à la source
lumineuse pour produire un minimum de 0,25 lux à 2 mètres. 0,25 lux équivaut à peu près à la
luminosité d'une pleine lune dans un ciel nocturne dégagé.
Figure 2 – Battery Replacement
1
sees this press as a signal to turn the light off and
switch to the other light source simultaneously.
**The times listed on the rear of the package
assume that you start with fresh batteries and use
only one mode.
Troubleshooting
If the Remix fails to light:
• Check the batteries for proper installation.
• Replace batteries if proper installation is confirmed.
• Check the light for water contamination on the
circuit board. The light will resume normal operation
once the water is shaken or blown out and the light is
left open until completely dry. If the light has been
contaminated with salt water, flush the unit with fresh
water and dry as described above.
USA– International 5-Year Warranty
WARRANTY – Princeton Tec warrants this product to
be free from defects in workmanship and materials
under normal use for 5 years. This warranty covers all
of the component parts of the product except batteries.
This warranty does not cover deterioration due to
normal wear or damage due to misuse, alteration,
negligence, accidents, or unauthorized repair.
Princeton Tec will repair or replace parts which are
defective in workmanship or materials.
After (3) unsuccessful attempts (within the warranty
period) to repair the product, you have the right to elect
replacement of the product or a refund of the purchase
price less allowance for use of the product. NO
INCIDENTAL OR CONSEQUENTIAL DAMAGES ARE
INCLUDED IN THIS WARRANTY. (Some states do not
allow the exclusion or limitation of incidental or
consequential damages, so the above limitations or
exclusions may not apply to you.) This warranty gives
you specific legal rights, and you may also have other
rights which vary from state to state.
Opération de commutation
Opération de commutation
LED
DISTANCE (Meters) 10
61H
COLOR
LEDs
DISTANCE (Meters) 0
Remplacement des piles
Remplacement des piles
2
Princeton Tec reserves the right to change product
specifications without notice.
FOR CALIFORNIA RESIDENTS:
WARNING: This product contains Bisphenol A (BpA) a
chemical known to the State of California to cause birth
defects or other reproductive harm.
Return Policy
If your light fails to operate, follow these simple steps:
1) Check batteries. Replace if necessary.
2) To send your light in for repair or replacement, first
contact Princeton Tec customer service at
1-800-257-9080 to request an RMA number. Please
have your light model, date of purchase and a brief
description of the fault your are experiencing. No
warranty repairs will be accepted without an RMA
number.
3) Return the light to: Princeton Tec, PO Box 8057
Trenton NJ 08650. Postage due and freight collect
items will not be accepted.
4)Upon receipt your light will be processed in about
two weeks. Please allow additional time for return
transportation from NJ.
Princeton Tec
PO Box 8057,
Trenton, NJ 08650
Phone: 609-298-9331
Fax: 609-298-9601
www.princetontec.com
© 2017 Princeton Tec
Betriebsartenschalter
Betriebsartenschalter
53H
28H
LOW
HIGH
52
10
Einlegen der Batterien
Einlegen der Batterien
3
73

Publicité

loading

Sommaire des Matières pour Princeton Tec REMIX RGB

  • Page 1 DISTANCE (Meters) 0 * Princeton Tec calculates total burn time as the time it takes for the light source to produce a minimum of 0.25 lux at 2 meters. 0.25 lux is about the equivalent of a full moon on a clear night.
  • Page 2 évacué l'eau en la secouant ou d’inutilisation. en soufflant dedans et après l’avoir laissée ouverte 3. Renvoyez la lampe sans piles à : Princeton Tec, PO REMARQUE : en raison d'une tension nominale plus jusqu'à ce qu'elle soit complètement sèche. Si de l'eau Box 8057 Trenton NJ 08650 U.S.A.