Technical Specifications - SVB 36545 Mode D'emploi

Kerosene Heater
EN

Technical Specifications:

Fuel: Kerosene
Tank capacity: 5 liters
Burning time: Approx. 15-17 hrs.
Size: 35 cm x Ø 33 cm
Weight: 4.1 kg
Set screws
Cover plate
Set screws
Supports
Burner head
Combustion cylinder
Tank display
Kerosene tank
Safety Information:
1. Check each component every time before using the
device. Make sure that there is sufficient air circulation
(keep windows and doors slightly opened)!
2. Only use pure kerosene. Do not use any other type of
fuel to operate the heater.
3. Avoid filling the heater with kerosene while it is in
operation. After filling, clean up any spilt kerosene and
close the tank securely.
4. Do not fill the device near any flammable objects.
5. Do not lay any objects, such as clothing on the heater
- (overheating and fire hazard)! Keep the device a safe
distance away from walls, furniture, etc.
6. Avoid moving the heater while it's in use.
7. Do not use the heater in direct sunlight or in high tem-
peratures.
8. Do not leave the heater on while unattended.
9. The heater should not be operated in drafty rooms.
10. Keep children away from the device while in use.
11. Store the heater in a dry area. The wick should be
stored separately from the wick holder and the tank.
4
ATTEnTION!
Do not use in
confined areas!
Set screws
Protective mesh
Mesh burner head cover
Chimney cover
Filler neck
Wick adjuster
Base plate
Filling with Kerosene:
Open the filler neck's lid and use the supplied funnel
to fill the tank. Pay attention to the tank status display.
Once the display shows "F", the tank is full. Close the lid
and clean up any spilt kerosene.
Ignition:
1. Wait 30 min. after filling, so that the wick can absorb
a sufficient amount of kerosene.
2. Turn the wick adjuster in a clockwise direction to its
max. height. Then, pull up the 3 set screws on the ou-
ter mesh screen to be able to light 2-3 sections with a
match.
3. Push the mesh screen back down and secure the set
screws
.
Regulating the Flame:
It takes approx. 5 min. for the flame to stabilize. After-
wards, you can set it to your desired height. Swing the
heater back and forth 2-3 times while holding on to the
carrying handle, then check the flame once more time.
• If the burner head's mesh is bright red, the flame is set
correctly.
• If the flame is flaring out of the burner head's mesh,
the wick is set too high.
• If the burner head's mesh isn't bright red, the wick is
set too low or the fuel tank is empty.
Changing the Wick:
1
2
Remove the safety
mesh and chimney.
3
Loosen the 4 wing nuts
and remove the cover.
4
Loosen the wick
adjuster by turning it
in a counter-clockwise
direction, then pull it
out towards yourself.
Maintenance and Care:
The wick is made out of fiberglass and has a very long
service life. If the wick is too dirty, it cannot be adjusted
properly. For this reason, it should be cleaned once per
month (with a screwdriver, etc.).
5
Pull the wick holder
and wick upwards and
take the wick out of its
holder.
6
Swap out the old wick
with a new one. The
new wick should protru-
de approx. 59 mm out
of the wick holder.
7
Place with wick holder
and wick back into the
heater – remove the
rubber gasket for easier
placement.
8
Fix the wick holder and
wick into place by using
the wick adjuster, then
put the rubber gasket
back into place.
9
After fully reassembling
the heater, test it in a
safe area.
5