Table des Matières
Publicité
IMPORTANT
Please read
these
instructions carefully before you start to assemble this product
.
Please
carry
out
the
steps in
the order
set
out
in
these
instructions.
Keep
these
instructions
in
a
safe
place
for future
reference.
Safety Advice
For
safety purposes we
strongly recommend the product to
be
assembled by at least
two
people.
Some parts may have sharp edges.
Please be
careful when handling components. Always wear
gloves,
eye
protection,
and long
sleeves
when assembling or performing any maintenance
on
your product.
Do
not
attempt
to assemble the product
in
windy or wet conditions.
Do
not
attempt
to assemble the product if you
are
tired,
have
taken drugs,
medications or alcohol, or if you
are
prone to dizzy
spells.
Dispose
of
all
plastic
bags safely
-
keep
them
away
from children's
reach.
Keep
children
away
from the assembly
area.
When using
a
stepladder or power tools, make
sure
that
you
are
following
the manufacturer's
safety advice.
Do
not climb or stand on the
roof.
Do
not hang or
lay
on the profiles.
Heavy articles should not
be
leaned against the poles.
Keep
roof
and
gutters
clear
of
snow,
dirt
& leaves.
Heavy snow load on
the roof
can make
it unsafe to stand below or nearby.
If
color
was
scratched
during
assembly it
can be
fixed.
Cleaning
Instructions
In
order to
clean
the product,
use
a
mild detergent solution and
rinse
with
cold clean water.
Do
not
use
acetone, abrasive cleaners, or
other
special
detergents to
clean
the
panels.
Clean
the product once assembly
is
complete.
Before Assembly
Choose
your
site
carefully before beginning
assembly.
The
ground
surface must
be
perfectly flat
and leveled and
have
a
solid
base such
as
concrete,
asphalt, deck
etc.
If
you've purchaced the
Arcadia Alpine Kit ground
surface must have
a
solid
base
of
concrete
or asphalt.
Sort the parts and check against the
content
parts
list.
Parts
should
be
laid
out
close at hand. Keep
all
small parts (screws etc.) in
a
bowl
so
they do
not get
lost.
Please
consult your
local
authorities if
any
permits
are
required prior to constructing the product.
The
drawings
in
this manual
are
designed for 4300 (12'x
14'),
5000 (12'x
16'),
6400 (12'x
21')
products
+ 0.7
or
2.1
Extension
Kits.
Please
note that content
list refers
only to 4300 (12'x
14')
product.
Note:
All
the extension module
steps are marked
with
a
dashed outline, should
be
performed during
the product's assembly
process.
During Assembly
cWhen encountering the information icon,
please refer
to the relevant
assembly step for additional comments and
assistance.
Attention
During assembly
use
a
soft surface below the parts to avoid scratches and
damages.
Please
make
sure
you install the panels
with the
UV
protected
side
out (marked with
"THIS
SIDE
OUT")
and remove the sticker
as
panels
are in place.
M
Steps
Step
1: If
you've purchased the
Arcadia Alpine
Kit, you should refer to their instructions
at
this point.
Step 5+9:
Use
silicone sealant on both
sides
of part
#
8969.
Step 10: Note the profiles' direction
by
the
holes on each edge,
see
drawing
b.
Step 25: If you've purchased the
Arcadia Alpine
Kit, you need
5
people to perform this
step.
Step 26: Note the direction
of
the bows
at
the products'
edges,
do not
tighten
the
screws in
drawing
b.
Step 27: Tighten the
screws
of
all
bows.
Step 35: Make
sure all
panels
are
placed
with
the
"THIS
SIDE
OUT" sticker facing up
.
Make
sure
the panels
are
inserted
all
the way into the profile
in
the middle.
Step 38: Make
sure
the edge profiles
are in
line
with
the longitudinal
beams,
see
drawing
c.
Step 42:
If
you've purchased the
Arcadia Alpine Kit,
please refer
to
its
assembly instructions.
Step 42: Check the product's diagonals and
make
sure
they
are
identical.
Please
level
the
posts and
adapt
screws
and plugs to your specific
foundation
type.
Tighten
all screws at
the end of assembly.
Do
not tighten
screws
and nuts (8192
&
466)
until completion of assembly
process.
These
2
icons
indicate if screws'tightening
is
required or not.
A
Note:
Anchoring this product to the ground
is
essential to
its
stability
and rigidity.
It
is
required to complete this
stage
in
order for your warranty to
be
valid.
Publicité
Table des Matières
