Align 3GX Manuel D'installation Et De Réglage page 10

Swashplate Settings
Enter Setup Mode Turn on transmitter, press/hold SET,
power on heli, release SET before
LEDs stop scrolling.
Setting 1 LED LED1 lit
Setting Mechanical Travel and Neutral point
setting
Setup Setup swashplate movement on TX,
Method set elevator forward and aileron right
cyclic angle limit to 8 degrees after
setting, return to zero degree pitch.
Setting 2 LED LED2 lit
Setting Elevator Travel Limit Setting
Setup Push elevator stick forward to limit,
Method and release.
Setting 3 LED LED3 lit
Setting Elevator gyro setting
Setup Tilt heli forward and back while
Method observing gyro correction direction. If
reversed, move elevator stick until
STATUS LED changes color to reverse
gyro direction.
Setting 4 LED LED4 lit
Setting Aileron Travel Limit Setting
Setup Push aileron stick to extreme right,
Method and release
Setting 5 LED LED5 lit
Setting Aileron gyro setting
Setup Tilt heli left and right while observing
Method gyro correction direction. If reversed,
move aileron stick until STATUS LED
changes color to reverse gyro
direction.
Setting 6 LED
Setting
Setup
Method
Warnings After completing setting of 8 degrees
SWASH, do not make further
adjustments. If adjustment to
helicopter's roll rate is needed, the
adjustment must be made in the roll
rate under flight mode's cyclic pitch
section.
Phil, alias Le Doc, janvier 2014
ANNEXE 2 :
Fichier d'aide officiel « Manual.mht »
Speed Governor Settings
Turn on TX, lower throttle all the way
down, press/hold SET, power on heli,
release SET after LEDs stop
scrolling.
LED1~5 all lit up
Speed governor setup
Push throttle open fully to complete
setup, indicated by flashing of LED
1~5, and then enter normal operation
condition.
Notice 3GX
Rudder Settings
With 3GX powered up, press SET for about one
second.
LED1 lit
wide/narrow servo band setting
Set servo wide/narrow band using rudder stick.
Green LED for standard wide band servos. For
narrow band servo, LED will be orange until
rudder stick is pushed 3 times to confirm setting
and status LED will turn to red.
LED2 Lit
Digital/Analog Servo Selection
Move rudder stick to select digital/analog servo.
Green STATUS indicates digital servo, red
indicates analog.
LED3 lit
Rudder Gyro NOR/REV Setting
Yaw the heli left/right while observing gyro
correction direction. If reversed, move rudder
stick to change direction.
LED4 lit
Rudder Servo Travel
Move rudder stick to left/right until rudder at
extreme end point, wait until STATUS change
from green to red.
LED5 lit
Heli Size and Delay Value
Move rudder stick to change STATUS color,
green STATUS for large heli more, red STATUS
for small Heli mode. Moving rudder stick to any
one side to set delay. The amount of delay is
determined by distance from center and keeps
the position. Press EXIT to set.
LED 1~5 all lit up
Gyro install reverse setting
Use rudder stick to set gyro install position.
Green STATUS is normal, red STATUS is install
upside down.
Flight Mode Setting
With 3GX powered up, push the rudder stick left or right, and
hold the SET button for about one second.
STATUS flashs green once
cyclic pitch speed adjustment.
Move aileron stick to increase/decrease the number of LEDs lit
between LED1~LED5. More LED's means faster rolls. Same
methods applies to elevator using elevator stick to control flip
rate. Aileron and elevator roll rate need to remain close, with
setting deviation to remain within 20%.
STATUS flashes green twice
Elevator travel limit setting
While in this mode, elevator may deviate forward/backward by
as much as 8 degrees + offset percentage. For example, LED
displays 50% settings, total elevator travel will be 8+0.5*8=12
degrees. Set to a value with no mechanical binding at extreme
end or keep default value at 70%.
STATUS flashes green 3 times
Aileron travel limit setting
While in this mode, aileron may deviate left/right by as much as
8 degrees + offset percentage. For example, LED displays 50%
settings, total aileron travel will be 8+0.5*8=12 degrees. Set to
a value with no mechanical binding at extreme end or keep
default value at 70%.
STATUS flashes green 4 times
Swashplate Dampening Setting
Move elevator stick to adjust collective pitch dampening level.
Move aileron stick to adjust cyclic pitch dampening. More LED's
indicates more dampening.
STATUS flashes green 5 times
Swashplate bump (acceleration) Setting
Move elevator stick to adjust collective pitch acceleration level.
Move aileron stick to adjust cyclic pitch acceleration level. More
LED's indicates more acceleration. If acceleration level exceeds
50%, check the BEC to ensure it can supply enough current to
servos. Dedicated receiver battery is recommended for
acceleration higher than 50%.
1. Flashing LED indicates 10%; fully lit LED indicates 20%.
For example, LED1 and LED2 are fully lit, while LED3 is
flashing, this is translated to 2*20+10=50%.
2. Move the stick to display the stick function's setting value.
For example, moving aileron stick will result in LED1~LED5
displaying aileron's setting value.
Page 10