Very Important - Orbis DATA MICRO + Instructions D'emploi

DATA MICRO + / DATA MICRO 2+
OPERATING INSTRUCTIONS
Increment or move up
in menu
Circuit C2 override
(only Data Micro 2 +)
C
Move back in menu
Permanent override
(C+C1 ó C+C2)
On / Off
Programming
Circuit 2
(only Data Micro 2 +)
Day of the week
(1) Monday
AM / PM mode
Hour : Minute
Circuit 1
On / Off
DESCRIPTION
+
DATA MICRO is a time switch designed to control any electrical installation.
Includes pulse programming from 1 to 59 seconds and up to 32 block memory
spaces. Automatic winter – summer official time adjustment.
INSTALLATION
ATTENTION: Electrical devices must be installed and assembled by authorized
installer.
VERY IMPORTANT: This time switch is protected internally against interference by a
safety device. However, particularly strong electromagnetic fields may alter its
operation. Such interference can be avoided by adhering to the following
recommendations during installation:
- The device should not be installed near inductive loads (motors, transformers,
contactors, etc)
- A separate power line is recommended (equipped with a network filter if
necessary)
- Inductive loads should be equipped with interference suppressors (varistor, RC
filter)
If the time switch is to be used in combination with other devices in an installation, it
is necessary to verify that no parasitic disturbances will be caused by the group.
MOUNTING: Electronic control device for independent installation in distribution
cabinet fitted with symmetrical 35 mm profile in accordance with the standard EN
60715 (DIN Rail EN 60715 (Rail DIN).
CONNECTION:
Connect according with the following schema:
DATA MICRO +
L
1 2 3 N
STARTING UP AND PROGRAMMING
+
DATA MICRO is already programmed with current date and time, and with the
official automatic winter – summer official time adjustment activated (last Sunday in
March and last Sunday in October).
Programming is based in menus (indicated by icons):
•
- Programming.
•
- Clock setting.
•
- Winter / summer official time change.
•
- Holidays period programming.
DIGITAL TIME SWITCH
Display
Decrement or move
down in menu
Circuit C1 override
C2 C1
OK
MENU
Confirms the selection
Starts menu
Clock setting
Summer / Winter time
Holidays program
Pulse
Override
Permanent overrride
DATA MICRO 2 +
4 5 6 L
1 2 3 N
RESET
Although the clock of the device is already programmed, if a RESET is needed
(blank display, inconsistent data, etc), press at the same time the four keys during 3
seconds. In this moment, the device loses all data and goes to clock setting mode,
directly to program year, month, day, day of the week, hour and minutes.
CLOCK SETTING. FIG 1.
For clock setting, press key
select icon and press
blinking; update the year by pressing keys
.
The same operation should be made to update month, day, day of the week, hour
and minutes. By accepting minutes with
To change the time mode (24h/12h am-pm) proceed as follows: accept year, month,
day and day of the week; while hour is blinking, press
time. After that, the time mode has change.
PROGRAMMING. FIG 2 and 3.
To program the device, press
menu is entered and the display shows the first programmed switching. If no
switching is programmed then - - : - - is shown. To program or edit the desired
switching press again, with keys
switching: C1 OFF, C1 ON, C1 ON
DATA MICRO 2+). Validate with
validating then with . Then select the days of the week that the switching has to
operate. With keys and
week that the switching has to operate and then fix it by pressing
sequence with the other days of the week when the switching has to operate. For the
days not desired, press to go down to the next day. After programming all the
days of the week, the display will show the next switching to program.
SHORT TIME SWITCHING (PULSE) PROGRAMMING. FIG 4.
If the selected switching is a Pulse
pulse starts, use keys and
59 seconds). This length is shown in the digits of seconds (situated at the right side
and smaller than the digits of hours and minutes). Select the day(s) of the week
when the switching has to be programmed and validate with
to come back to normal mode. If
two minutes, the device returns to normal mode.
VIEWING PROGRAMMED SWITCHING. FIG 5.
The programmed switching can be checked by entering again in menu
pressing key all the switching are shown in display, and after the last one, the
display shows - - : - -, if there is any free space and then it shows the number of free
spaces.
EDITING OR DELETING SWITCHING
Programmed switching can be edited or deleted in menu
or the switching to be edited or deleted. To edit it, proceed as in clause
PROGRAMMING and to delete it, keep pressing key
To delete all the switching without using RESET, go to the point where the display
shows the free spaces of memory, keep pressing key
. The display will show 32, the total free memory spaces.
MANUAL OVERRIDE. FIG 6.
In normal mode, pressing key
The same for circuit C2 by using key
If any manual override is executed, it is represented in display by symbol
The next programmed switching cancels the manual override and the symbol
disappear from the display.
PERMANENT OVERRIDE. FIG 7.
This option blocks all the programmed switching. In normal mode, keep pressing key
and then press key (
this situation is indicated in display with symbol
can be changed by pressing key
To cancel permanent override keep pressing key
( ), symbol disappear from display. The same for circuit C2 using key
( ) only in DATA MICRO 2+.
WINTER / SUMMER OFFICIAL TIME CHANGE. FIG 8.
Enter MENU by pressing key
validate with . There are the three following working modes:
AUTO: The clock is automatically changed on the last Sunday in March al 02:00
and the last Sunday in October at 03:00.
PRO: Allows to choose the date and time for the time change, programming first
the winter – summer change (
OFF: No time change will be made
HOLIDAY PROGRAM. FIG 9.
This function allows deactivating the circuits during a period of time up to 99 days.
After that, the programming continues as usual.
If user validates 0 days, the holiday period is cancelled and the device will work in a
normal way. If user validates a number of days different than 0, the device starts
immediately, so relays switch to OFF and programmed switching will not execute.
If the validated number of days is 1, the holiday period will finish at 23:59:59 of the
same day than validation. If the validation number of days is 2, the holiday period will
finish next day. And so on.
Display shows symbol during the holiday period.
to access to the Menu and with keys
. Display shows the year with the last two figures
and and validate it with key
, it automatically goes to normal mode.
and
to enter to the menu. By pressing again
and select the circuit and type of
, (C2 OFF, C2 ON, C2 ON
and introduce hour and minutes desired,
place the blinking cursor on the first day of the
, after introducing hour and minutes when the
to program the length of the pulse (from 1 to
. After that, press
is not pressed, being in any mode, after
, selecting with keys
and then press key
and then press key
( ), circuit C1 is activated or deactivated.
( ) (only in DATA MICRO 2+).
) to activate the permanent position of circuit;
. After that, the state of the circuit
( ).
and then press key
; select option using keys
) and then the summer – winter change (
and
at the same
the
only in model
. Repeat this
and
.
.
and ,
).