Publicité
garden
and
gardening
1M
SAFETY ADVICE
Rion
is
not responsible for the
misuse
of tools
or parts.
It
is
of utmost importance to
assemble
all
of
the parts according to the directions.
Please
follow them
closely and
do
not
skip any step.
We
strongly recommend
using
work
gloves
during
assembly.
If using
a
step ladder or
power tools
ensure
that
you
follow the manufacturer's
safety advice.
If local
building
codes
require permits or licenses make
sure
that they
are
acquired before beginning.
Your Greenhouse
should
be secure by
anchored to the prepared
foundation
using the recommended hardware.
Do
not attempt to
assemble
the greenhouse
in
windy
or
wet conditions.
Dispose
of
all
plastic
bags safely keep
them out of
reach
of
small
children.
Keep
children away from the assembly
area.
Do
not
lean
against or push the greenhouse during construction.
Do
not attempt to
assemble this greenhouse
if
you
are
tired,
have
taken drugs or alcohol or if you
are
prone to
dizzy spell.
When
your Greenhouse
is
fully
assembled examine it for sharp edges and
trim with
a
razor knife if necessary.
If
you live
in
a
hot climate, where outside temperatures
exceed
46°
C
(115°
F)
in
the
sun
or
36°
C
(99°
F)
in
the
shade,
this may
cause
the temperature inside the greenhouse to
exceed
55°
C
(131°
F).
Such
conditions
may harm
your plants and will damage the greenhouse by warping structural profiles.
In
order to prevent damage:
Ensure
good ventilation during hot
days.
Make sure
that the temperature
inside the green house never exceeds
55°
C
(131°
F)
by
providing
a
shading
screen, such
as
the
Shade Net (available
as
an
accessories
option).
Note:
RION
is
not responsible for
any damage due
to high temperatures.
* Always close
roof vent
in
high winds.
REQUIRED TOOLS
GT1
-
Special
tool
to connect pins through lined up
holes. Pin Tool
fix and lock profiles in place
To
assemble this
product you will
need the
following
tools
(these
items are
not
supplied)
411
BEFORE ASSEMBLY
Rion
is
not responsible for the
misuse
of
tools or parts.
Selecting
a
site
-
the greenhouse must
be,
positioned
and fixed on
a
flat
level surface.
Sort
the parts and check according to the contents parts
list. Do
not begin assembly if
any parts
are
missing.
If you prepare
a
concrete
foundation
do not excavate and pour concrete
in
frozen ground.
We
recommend that
you place
your Greenhouse
in
a
spot where it will
receive
direct sunlight
and
will
be
protected from the
wind
as
much
as
possible. The
door should not
face
prevailing winds.
DURING ASSEMBLY
Step
1: Place
door hinge according to the
desired side you wish to install the door,
to the right
or the left side
of
the
Sun
Room
/
Sun
Lounge.
Steps 1-4, 18, 22: Arrange
all 2D
connectors with the stamped word
OUT
facing the outside of the greenhouse.
Step 5:
Make sure
that
the frame
is
perfectly straightened
by measuring the diagonals and
verifying that they
are
the
same.
Make sure
that
the frame
is
level and
anchor it with screw/screw
+
dibble/spike (not supplied) according to the
selected surface.
The
wall to which you
are
securing your
Sun
Lounge must
be 90°
to the foundation
Steps
9, 10: Walls
assembly must
be
made gradually (1.panel 2.rofile 3.connector) according
to describe method
in
step
#8
Step 27: Make
sure
that
the top frame
is
leveled
with
wall.
Fix
it using one
of
the two options illustrated with
a
screw/bolt
+
plugs (not supplied) according to the selected wall.
Steps 44, 49: Insert the rubber strip from the outside
the greenhouse.
Cut
the remaining
edges
as
needed.
*Relevant only for
sun
room/lounge with
clear panels.
Attention:
DWhen
encountering the information
icon, please refer
to the
relevant assembly step for additional comments and
assistance.
This icon
indicates
that
the installer should
be
inside the product.
Publicité
