Operating Sequence; Care And Cleaning; External Cleaning - White-Westinghouse Frigidaire XDEX75NZ Manuel De L'utilisateur

Operating Sequence

1. Check that the lint fi lter is
clean and in place.
2. Load the dryer and close the door.
Load items loosely. The average wet load will fi ll the drum
1/3 to 1/2 full. Items need room to tumble freely for even
drying and less wrinkling. If desired, place a dryer fabric
3. Select the appropriate programme and settings for each load.
Turn the programme selector dial (1) in either direction to
select the programme desired. The estimated drying time

Care and Cleaning

IMPORTANT:
You must DISCONNECT the appliance from the electricity
supply, before you can carry out any cleaning or maintenance
work.

External cleaning

Use only soap and water and then dry thoroughly.
Important: do not use methylated spirit, diluents or similar
products.
Cleaning the fi lter
Your dryer will only function well if the fi lter is clean.
Clean the lint («fl uff») fi lter after every load. Lint build-up on
the fi lter restricts air fl ow, which causes longer drying times.
The fi lter is located at the bottom of the door opening.
Remove fi lter by pulling straight up. Remove the lint and
replace the fi lter.
softener sheet on top of
the load at the beginning of
the cycle. To save energy
and time and avoid un-
even drying and wrinkling,
do not overload the dryer.
When drying large items,
dry only two or three items
at a time. Fill out the load
with small and medium
sized items. For delicate or
very small loads, add two
or three similar items to
improve tumbling action.
for Auto Dry cycles or the actual drying time for Timed Dry
cycles will be displayed. A suitable drying temperature,
dryness level and options will automatically be indicated for
the cycle selected. See the «Programme Table» for more
details. To change the drying temperature and dryness
level, press the Temperature (2) and Dryness (3) buttons to
scroll to the desired settings. To select or delete an option,
press Options (4); then, while the indicator is blinking, press
Select (5). The indicator will light when the option has been
selected. It will no longer be lighted when the option has
been deleted. Adjustments made to a programme will be re-
membered and recalled each time that programme is selected
in the future. To return to factory settings, press the Start/
Pause (7) and Select (5) buttons at the same time and hold until
the signal sounds.
4. Start the programme by pressing button 7.
Close the door and press Start (7)to begin the programme.
The dryer will not operate with the door open. To interrupt
the programme, press Pause (7); press Start (7) to resume
the programme. Press Cancel (6) to stop the programme.
If changes to the programme, temperature, dryness level or
options are attempted after the programme starts, the lights
will blink and a signal will beep. To change the programme
once it has begun, press Cancel (6) and select a new pro-
gramme. To change the temperature, dryness level or op-
tions once the programme has begun, press Pause (7) and
make the new selections. A signal will sound at the end of
the cycle if the signal volume option has been selected.
5. When the programme ends...
• Remove the items promptly and hang or fold.
• You are advised to unplug the appliance.
• Clean the fi lter after every drying programme. A clean fi lter
ensures correct functioning of the appliance.
Cleaning the drum and
moisture probes
Occasionally a waxy build-
up may form on the lint fi lter
and/or moisture sensing
bars in the back of the drum
from using dryer-added
fabric softener sheets. To
remove this build-up, wash
them with warm, soapy wa-
ter. Dry the fi lter thoroughly
and replace. Do not operate
the dryer without the lint fi lter in place.
CAUTION!
Do not use furniture cleaners or aggressive cleaning agents
to clean the machine. Use a damp cloth to wipe down the
operating screen and housing.
9