Panasonic TC-P42C1 Manuel D'utilisation page 29

(Continued)
Sets the mode to select the channel with Channel up/down button
(All/Favorite/Digital only/Analog only)
•
Favorite: Only channels registered as FAVORITE (p. 20)
Selects the screen menu language (p. 16)
Adjusts the clock (p. 17)
Sets channels (p. 39)
Selects the terminal and label of the external equipment (p. 41)
Prevents "Image retention" with Wobbling. (Automatic/Periodic)
•
Automatic: Shifts the display image automatically.
•
Periodic: Shifts the display image every (1/2/3/4) minutes according to what was set in the "Time (minutes)" menu.
Sets the time for "Pixel orbiter-Periodic" setting. (1/2/3/4)
Change the brightness of the side bar (Off/Dark/Mid/Bright) (4:3 mode only)
•
The recommended setting is "Bright" to prevent panel "Image retention". (p. 48)
Press "OK" to start horizontal "Scrolling" on the screen (p. 48)
Controls equipment connected to HDMI terminals (p. 32) (On/Off)
•
"Power off link", "Power on link", "Stand-by power save", "Auto power stand-by" and "Default speakers"
cannot be selected if "Off" is set.
Sets "Power on link" of HDMI connection equipment (p. 32) (Yes/No)
Sets "Power off link" of HDMI connection equipment (p. 32) (Yes/No)
Set "Stand-by power save" of HDMI connection equipment. (p. 32) (No/Yes)
Set "Auto power stand-by" of HDMI connection equipment. (p. 32)
(No/Yes (with reminder)/Yes (no reminder)
Selects the default speakers (p. 32) (TV/Theater)
To conserve energy, the TV automatically turns off when NO SIGNAL and NO OPERATION is performed
for more than 10 minutes. (Enable/Disable)
Note
•
Not in use when setting "Auto power on", "On/Off Timer", "Lock", "SD mode" or Digital channel.
•
"No signal for 10 minutes was activated" will be displayed for about 10 seconds when the TV is turned
on for the first time after turning the power off by "No signal for 10 minutes".
•
The on-screen display will flash 3, 2 and 1 to indicate the last three (3) remaining minutes prior to the shut-off.
To conserve energy, the TV automatically turns off when no operation of remote or side panel key
continues for more than 3 hours. (Enable/Disable)
Note
•
Not in use when setting "Auto power on" or "On/Off Timer".
•
"No activity for 3 hours was activated" will be displayed for about 10 seconds when the TV is turned on
for the first time after turning the power off by "No activity for 3 hours".
•
The on-screen display will flash 3, 2 and 1 to indicate the last three (3) remaining minutes prior to the shut-off.
Turns TV On automatically when the cable box or a connected device is turned On (No/Yes)
TV AC cord must be plugged into this device. TV comes on every time the power is restored.
•
The "Sleep" timer, "On / Off timer", and "First time setup" will not function if "Auto power on" is set. (p. 42)
Set "Thumbnail" or "Slideshow" to play back SD cards automatically. (Slideshow/Thumbnail/Set later/Off)
Displays TV version and software license.
Performing Reset will clear all items set with Setup, such as channel settings. (p. 38)
Sets the mode to select the channel with Channel up/down button (All/Favorite/Digital only/Analog only)
Sets favorite channels. (p. 20)
Changes the station identifier. (p. 39)
Checks the signal strength if interference or freezing occurs on a digital image. (p. 39)
Adjustments/Configurations (alternatives)
Adjustments/Configurations (alternatives)
Channel surf mode
All
Language
Clock
ANT/Cable setup
Pixel orbiter Automatic
Time (minutes)
4
4:3 side bars Bright
Scrolling bar
VIERA Link On
Power on link
Yes
Power off link Yes
Stand-by power save
No
Auto power stand-by
No
Default speakers TV
No signal for 10 minutes
Enable
No activity for 3 hours
Disable
Auto power on
No
Play SD card automatically
Set later
About
Reset to defaults
29