Check whether the appliance is not damaged!
Protection equipment and slightly damaged parts need to
be checked carefully whether they still work perfectly
before being used again. Check whether the movable
components work perfectly and are not jammed or
damaged. All components must be fitted correctly and
satisfy all conditions to ensure perfect working of the
appliance. Any damaged protection equipment and
components must be repaired or replaced in an authorised
shop unless otherwise specified in the Operating
Instructions. Have any damaged switches replaced in a
service shop. Do not use devices where the switch cannot
be turned on and off.
CAUTION!
Use of other extensions and accessories can represent a
risk of injury. Use only extensions and accessories which
are specifically described in the operating instructions and
recommended by the manufacturer.
Have your appliance repaired by an electrician only!
This appliance is in accordance with appropriate safety
provisions. Repairs can only be executed by an electrician,
using original or identical spare parts, otherwise there is a
risk of injury for the user.
Special safety instructions
Warning:
If having a strange feeling or the skin of your hands gets
coloured when using the appliance, stop working
immediately. Take adequate working breaks.
If the appliance is used more often, contact your
authorised dealer and buy anti-vibration accessory
equipment (handles).
Do not use the appliance at temperatures of 10°C and
lower. Make a work plan by which you will reduce the
exposure to vibrations.
Warning:
Some noise exposure cannot be avoided with this
appliance. More noisy works to be performed at an
admissible and suitable time. Adhere to the breaks and
limit your work to a necessary time. Use appropriate ear
protectors as personal protective equipment for you and
bystanders.
Warning:
High speed steel drilling heads, chisels, planes, scissors
and knives may only be sharpened with the appliance.
Do not use the appliance to grind other workpieces.
Never use the appliance with water.
Residual risks
Even if the appliance is used professionally, there is still
some residual risk that cannot be avoided. The following
potential risks may be derived from the type and design of
the appliance:
1. Grinding wheel sparks (risk of burn)
2. Contact with the sharp edge of the workpiece (risk of
going off the cutting)
The multi-purpose sharpener can work
continuously for a maximum of 15 minutes and
then needs to cool down for at least half an
hour.
The multi-purpose sharpener is suitable for
sharpening in dry conditions and must in no
case come into contact with liquids.
The multi-purpose sharpener can only be used
for sharpening of HSS (High Speed Steel) drills,
knives and scissors with straight cutting edges,
plane and chisel blades.
Sparks are generated when sharpening. Keep
the multi-purpose sharpener in a safe distance
from flammable liquids and materials.
Make sure you do not touch the sharpening
stone and processed material just after using
them as they are very hot.
If the processed material turns blue during the
sharpening process, it is overheated and can get
damaged. Cool the processed material regularly
when being sharpened, e.g. by water.
Additional safety instructions
To prevent any malfunction, damage and health
problems, please follow these safety instructions:
1.
When sharpening the workpiece, it is necessary
to wear gloves at all times as the workpiece is
very hot after being sharpened.
2.
Wear protective glasses at all times. Your
common glasses only have standard lenses.
THEY ARE NO protective glasses.
3.
Unattended starting to be avoided. The switch
must be off when plugging the appliance.
4.
The appliance is not suitable for outdoor works.
5.
Prevent any physical contact with the rotating
grinding wheel.
6.
Never use the universal grinder in an explosive
or flammable environment. Common engine
sparking may ignite a flammable material.
7.
If the grinding wheel is damaged, it must be
immediately replaced.
8.
Set the distance between the grinding wheel and
the knife support to 2 mm.
9.
The grinding wheel must rotate evenly. The
grinding wheel needs to be changed if there are
vibrations.
10. Do not use any damaged and deformed grinding
wheels.
11. Grinding wheels recommended by the
manufacturer with specification of the rotation
speed equalling to or exceeding the speed
specified on the type label of the electric tool to
be used only.
12. Instructions for the safe use, handling and
storing of grinding wheels need to be followed,
considering the CEN standard requirements for
grinding products for the electric tool type
described by the standard. It is expected that
wheels are not additionally machined. If
additional machining of wheels is planned,
appropriate safety measures must be taken.
13. The unit must always be sure horizontally
and firmly attached with suitable screws on
the workbench. Watch for a secure
attachment of the device on a suitable
surface. Make sure that all fittings are tight.
14. Switch the appliance off and unplug it if the
feeder cable is damaged. A damaged feeder
cable must be replaced by the manufacturer, its
customer service centre or a similarly qualified
person.
15. The grinding wheel must be replaced if the
diameter is less than 46 mm.
Caution! You must not replace the grinding wheel. A
damaged or worn-out grinding wheel must be
replaced by the manufacturer, its customer service
centre or a similarly qualified person.
25