Publicité
Liens rapides
EZO Series Barrier-Free Water Coolers
EZO
EZO
35
19
24
36
8
5
9
Uses HFC-134A refrigerant
Usa refrigerante HFC-134A
Utilise du fluide frigorigéne HFC-134A
6
See FIG. 3
7
23
1
21
EZO4*1E
INSTALLATION, CARE & USE MANUAL
Manual de Instalación, Cuidado y Utilización
Manuel d'installation/entretien/utilisation
T M
TM
La Barrera de la serie Liberta Agua Coolers
TM
Coolers d'Eau de Barrière-Libère de feuilleton
39
34
3, 4
Sensor Eye
Adjustment screw
31, 32, 43
EZO8*1E
12
15
27, 28, 29
FIG. 1
Page
1
18
13
16, 17
23
45
44
See FIG. 4
37
7
38
20
25
26
30
98940C (Rev. B - 11/12)
Publicité
Manuels Connexes pour Elkay FLEXI-GUARD EZO4 1E Série
Sommaire des Matières pour Elkay FLEXI-GUARD EZO4 1E Série
- Page 1 EZO4*1E EZO8*1E INSTALLATION, CARE & USE MANUAL Manual de Instalación, Cuidado y Utilización Manuel d’installation/entretien/utilisation EZO Series Barrier-Free Water Coolers La Barrera de la serie Liberta Agua Coolers Coolers d’Eau de Barrière-Libère de feuilleton 16, 17 Uses HFC-134A refrigerant Usa refrigerante HFC-134A Utilise du fluide frigorigéne HFC-134A 3, 4 Sensor Eye...
- Page 2 EZO4*1E EZO8*1E FIG. 2 Page 98940C (Rev. B - 11/12)
- Page 3 EZO4*1E EZO8*1E HANGER BRACKETS & TRAP INSTALACIÓN DE LOS SOPORTES INSTALLATION DES SUPPORTS FIJADORES Y EL PURGADOR DE SUSPENSION ET DU SIPHON INSTALLATION Retire el soporte fijador que se encuentra 1) Retirez le support de suspension fixé au dos du 1) Remove hanger bracket fastened to back of conectado a la parte posterior del enfriador refroidisseur en retirant une (1) vis.
- Page 4 EZO4*1E EZO8*1E Service Instructions Bubbler Lower and Upper Shroud To access the refrigeration system and plumbing connections, remove four screws from bottom of cooler to remove the lower shroud. To remove the upper shroud for access to the pushbars, regulator, solenoid valve or other components located in the top of the unit, remove lower shroud, disconnect drain, remove four screws from tabs along lower edge of upper shroud, unplug two wires and water tube.
- Page 5 EZO4*1E EZO8*1E SENSOR RANGE ADJUSTMENT: The electronic sensor used in this cooler is factory pre-set for a “visual” range of 36 inches (914 mm). If actual range varies greatly from this or a different setting is desired, follow the range adjustment procedure below: Using a small tip screwdriver, locate range adjustment screw through the small hole between the sensor lenses (See Page 1.) Turn this screw clockwise to increase range and counterclockwise to decrease range (See Fig.
- Page 6 EZO4*1E EZO8*1E Cleaning the strainer To clean the strainer, unscrew the cap of the solenoid valve. Remove screen and rinse thoroughly with water. Insert screen back into solenoid valve and screw cap on. Make Screen sure the o-ring is placed properly. Malla Limpieza del filtro Ecran...
- Page 7 PARA PIEZAS, CONTACTE A SU DISTRIBUIDOR LOCAL O LLAME AL 1.800.323.0620 IMPRIMÉ AUX É.-U. POUR OBTENIR DES PIÈCES, CONTACTEZ VOTRE DISTRIBUTEUR LOCAL OU COMPOSEZ LE 1.800.323.0620 ELKAY MANUFACTURING COMPANY • 2222 CAMDEN COURT • OAK BROOK, IL 60523 • 630.574.8484 Page 98940C (Rev. B - 11/12)