Installation; Display And Battery Case Installation; Battery Type; Battery Substitution - Elesa MPI-15 Manuel D'utilisation

The magnetic band M-BAND-10 is made of two separate parts: the
magnetic band and the cover strip. The magnetic band is made of
a magnetic tape, a carrier strip and an adhesive tape (Fig. 2). The
cover strip is made of a protection strip and an adhesive tape (Fig. 1).
Fig.1
Cover strip
Protection strip (0.1 mm)
Adhesive tape (0.13 mm)
Fig.2
Magnetic band
Magnetic tape (1 mm)
Carrier strip (0.3 mm)
Adhesive tape (0.13 mm)
M-BAND-10 Technical data
Accuracy class ± 40 µm
magnetic tape: nitrilic rubber
carrier strip: stainless steel
Material
cover strip: stainless steel
acrylic adhesive tape
magnetic band: 10 mm ± 0.20 mm
Width
cover strip: 10 mm ± 0.20 mm
magnetic band: 1.43 ± 0.15 mm
Thickness
cover strip: 0.23 mm
Magnetic pole pitch 5 mm
Operating and storage
min -40°C max +100°C
temperature
Linear thermic expansion factor 17 x 10

3. Installation

3.1 Display and battery case installation

1) Make a drilling of 42 mm x 90
+0.2/+0.5
for the installation of the display.
2) Fix the display to the panel by using the specific mounting bracket
(the screw is included in the supply).
3) Make a drilling of diameter 34
installation of the battery case.
4) Fix the battery case to the panel by using the specific nut.
5) Fix the magnetic sensor by using M3 screws (not included in the
supply). Distance between sensor and magnetic tape to ensure a
correct reading of the displacement: max 2.5 mm.
Drilling template for display
(remove all drilling burrs before fitting the display / battery case)
+ 0.5
90
+ 0.2
R
max 1
ELESA models all rights reserved in accordance with the law. Always mention the source when reproducing our drawings.
Fig.3
Proper assembling
Cover strip
Magnetic band
/K
-6
mm in the metal sheet
+0.2/+0.5
mm in the metal sheet for the
+0.2/+0.5
Drilling template for battery case
+ 0.5
34
+ 0.2
Magnetic length and angle measuring system MPI-15
The cable layout should be outlined to prevent damages due
to cable strain or contacts of the cable with other machine
components. It is recommended that the cable is installed sufficiently
far from magnetic / electromagnetic sources.

Battery type

Batteries are not supplied together with the MPI-15. The following
standard battery is recommended: 1 x C battery

Battery substitution

When the display shows the battery symbol, the battery should be
replaced as soon as possible. After the removal of the battery, the
display memory is buffered for approximately 60 seconds. Substitute
the battery within this time frame.

3.2 Magnetic band installation

The cover strip must be installed over the magnetic band to protect it
from possible mechanical damages.
1) Clean the mounting surface carefully.
2) Remove the protective foil from the adhesive tape of the magnetic
band.
3) Stick the magnetic band on the mounting surface.
4) Clean the surface of magnetic band carefully.
5) Remove the protective foil from the adhesive tape of the cover
strip.
6) Stick the cover strip on the magnetic band.
7) In the absence of a seat for the housing of M-BAND-10, secure
the ends of the cover strip to prevent unintentional peeling.
The mounting surface must be flat. Buckles or bumps will
lead to measuring inaccuracies.
To guarantee an optimal adhesion of the adhesive tapes, the
mounting surfaces must be perfectly cleaned, dry and smooth.
The following surface roughness is recommended: Ra <= 3,2 N8
(Rz <= 25). To maximize the adhesion install the strip applying
pressure. Gluing should preferably be carried out at temperatures
between 20 °C to 30 °C and in dry atmosphere.
Once the installation is completed, the calibration procedure must be
carried out as shown at Paragraph 7.
13