LUXSAR VDR840C Guide Rapide page 4

•
To set up dome protocol and ID, press MENU to access the Main menu, and select <Camera Setup>. The available
protocols include <DynaColor>, <Pelco D>, <Pelco P>, <AD422> and <None> (default). Note that ID number must
match the ID address defined by the dome.
•
To configure the RS-485 parameters, select <System Setup> from Main menu, and then select <RS485 Setup>. The
default Luxsar VDR840C/VDR440C RS-485 settings are 9600 Baud, 8 Data Bits, 1 Stop Bit and No Parity.
Dome Control Button:
Basic Playback Operation
Searching Recorded Video by Time:
•
Press SEARCH button to enter the Search menu; the From Time and End Time of the available video is listed on top of
the screen. The value is unchangeable.
•
Use Direction buttons to move the cursor for setting the Start Time; adjusting the date and time values by UP/DOWN
keys. Press ENTER to confirm or ESC to abort.
•
Move the cursor to <Begin Playback> and press ENTER to start playing back the selected video. Press PLAY/STOP
again to return to live video.
NOTE: If there is no available recorded video that matches your specified time and date, the unit starts to playback
from the next available video.
Searching Recorded Video by Event:
•
Press SEARCH button to enter the Search menu.
•
To search event video that was recorded on a specific camera, use LEFT/RIGHT keys to move the cursor and press
ENTER to select or de-select a channel.
•
Move the cursor to <Event List> and press ENTER to list the event video of the selected channels.
•
The list displays each event by date, time, triggered camera and alarm type. The latest recorded event video will be
listed on the top. To exit the event list, press ESC.
•
Use UP/DOWN to scroll through the Event List. Press ENTER to play back the selected event record.
Playback Controls:
Button Description
The button is for rewinding the recorded video while playing back. Press the button repeatedly to increase the
LEFT
speed of reverse playback by 1×, 2×, 4×, 8×, 16×, or 32×.
The button is used to play the recorded video fast forward. Press the button repeatedly to increase the speed of
RIGHT
forward playback by 1×, 2×, 4×, 8×, 16×, or 32×.
Press FREEZE to pause the playback video. When the recorded video is paused, press LEFT / RIGHT to resume
FREEZE
playback video single step reverse / forward respectively. Press FREEZE again to continue playing video.
PLAY/STOP Press to play back video or to stop playing back video and back to live mode.
Using Remote Software
Setup Requirements:
•
Network connection to PC.
•
IP address of your Luxsar VDR840C/VDR440C. To check the DVR's IP address, press MENU key on the unit and enter
password to access OSD Main menu; select <System Setup>, <Network Setup> to check the IP.
Changing Internet Setting:
•
Start IE; select <Tools> from the main menu of the browser, then <Internet Options> and then click the <Security>
tab.
NOTE: To use the LuxsarRemote remote software, ActiveX component is required, and of all web browsers, only IE
supports ActiveX.
•
Select <Trusted sites> and click <Sites> to specify its security setting.
•
Disable Require server verification (https:) for all sites in this zone. Type the IP address of the unit in field and click
<Add> to add this website to the zone.
•
Click <OK> to accept the settings and close the <Security> screen.
Using the Remote Software:
•
Start IE and enter the IP address of your Luxsar
•
The ActiveX controls and plug-ins dialog will show twice for confirmation, click <YES> to accept ActiveX plug-ins. The
LuxsarRemote plug-ins will be downloaded and installed on your PC automatically when the connection is successfully
made.
NOTE: Do not enter any leading 0 characters in the address, for example, "192.068.080.006" should be entered
"192.68.80.6".
NOTE: If the default trigger port 80 is changed into another one, port 81 for example, you should enter the IP address as
"192.68.80.6:81".
•
Version verification starts automatically to verify whether LuxsarRemote was installed. This process may take up to 30
seconds.
•
When the software is completely downloaded, the Login Screen is displayed.
•
Enter your username and password. The default username and password is: user/ 4321.
Viewing
live
camera
Instant
recording
Audio On/Off
Selecting display
mode
For more information on LuxsarRemote, see LuxsarRemote user's manual.
LuxsarRemote Lite Playback
To Playback Local *.drv File:
•
Click <Open> and the file selection screen is displayed. Select the *.drv video file to playback and click <OK>.
•
Click <OK> in the <Local Playback> Screen to start the operation, or click <Cancel> to abort the playback.
•
View the video playback using the Playback controls.
•
After playback, click <Live> to return to live video.
Playback Controls:
VDR840C/VDR440C in the address field.
Viewing Entering
playback configuration Bandwith
video menu selection