Eco Fluval Mode D'emploi page 2

IMPORTANT SAFETY INSTRUCTIONS
EN
WARNING – To guard against injury, basic safety precautions should be observed,
including the following:
READ AND FOLLOW ALL
1.
SAFETY INSTRUCTIONS
and all the important notices on the appliance before using. Failure to do so may
result in loss of fish life and/or damage to this appliance.
2. DANGER – To avoid possible electric shock, special care should be taken since
water is employed in the use of aquarium equipment. For each of the following
situations, do not attempt repairs yourself; return the appliance to an authorized
service facility for service or discard the appliance.
A. If the appliance shows any sign of abnormal water leakage, immediately
unplug it from the power source.
B. Carefully examine the appliance after installation. It should not be plugged
in if there is water on parts not intended to be wet. If the appliance or any
part of it falls into the water DO NOT reach for it. First unplug the unit before
retrieving.
C. Do not operate any appliance if it has a damaged cord or plug, or if it is
malfunctioning or it is dropped or damaged in any manner. The power cord of
this appliance cannot be replaced; if the cord is damaged, the appliance
should be discarded. Never cut the cord.
D. To avoid the possibility of the appliance
plug or receptacle getting wet, position
the appliance to one side of a wall mounted
receptacle to prevent water from dripping
onto the receptacle or plug. A "drip loop"
(see illustration 1) should be arranged
by the user for the cord connecting
appliance to a receptacle. The "drip loop"
is that part of the cord below the level
of the receptacle or the connector if an
extension cord is used, to prevent water
travelling along the cord and coming in contact with the receptacle. If the
plug or receptacle does get wet, DO NOT unplug the cord. Disconnect the
fuse or circuit breaker that supplies power to the appliance. Then unplug and
examine for presence of water in receptacle.
3. This appliance is not intended for use by persons (including children) with
significantly impaired physical or mental capabilities, unless they have been
given supervision or instruction concerning the use of the appliance by a person
responsible for their safety. Children should always be supervised to ensure that
they do not play with the appliance.
4. To avoid injury, do not touch moving parts or hot parts.
5. CAUTION - Always unplug or disconnect all appliances in the aquarium from
electricity supply before placing hands in water, before putting on or taking off
parts and while the equipment is being installed, maintained or handled. Never
yank cord to pull plug from outlet. Grasp the plug and pull to disconnect. Always
unplug an appliance from an outlet when not in use.
6. Do not install or store the appliance where it will be exposed to weather or
temperatures below freezing. FOR INDOOR HOUSEHOLD USE ONLY.
7. Make sure the appliance is mounted correctly and securely positioned on the
aquarium before operating the appliance.
8. This appliance was designed for use over a glass aquarium cover or acrylic top.
DO NOT USE OVER OPEN WATER. FOR HOUSEHOLD USE ONLY.
9. If an extension cord is necessary, a cord with proper rating should be used. A
cord rated for less amperes or watts than the appliance rating may overheat.
Care should be taken to arrange the cord so that it will not be tripped over or
pulled. The connection should be carried out by a qualified electrical installer.
SAVE THESE INSTRUCTIONS
10.
For the complete use and understanding of this product it is recommended that this
manual is thoroughly read and understood. Failure to do somay result in damage to this
product.
INSTALLATION AND USAGE:
Please verify that all components of the light fixture are undamaged before putting it into
operation. Before any kind of maintenance, always disconnect electrical supply of the light
fixture. This appliance was designed for use over a glass aquarium cover or acrylic top.
DO NOT USE OVER OPEN WATER.
• Make sure the light fixture is mounted correctly and securely positioned on the aquarium before
operating the appliance.
• Always ensure that the brackets are on the outside of the aquarium frame. If needed, the
extendable mounting brackets can be adjusted accordingly to ensure proper fit on aquarium.
• Sensor wire from light fixture: remove the adhesive backing from the sensor and affix it to the
outside glass of the aquarium. Position the sensor so that it will have a direct, line-of-sight to your
remote.
• Connect the plug from the transformer to the plug on the fixture.
• Connect the transformer to electrical supply.
REMOTE CONTROL:
• Follow "Installation and Usage" Instructions.
• Ensure sensor wire from the light fixture is positioned so that there is a direct, line-of-sight from
the sensor to your remote.
• Remove plastic cover from wireless remote; remove the clear plastic tab located at the bottom of
the remote to activate battery connection (remote should already have the battery included).
To operate:
• Point the remote so that the infrared sensor on the remote activates
the sensor on the light fixture.
To change the battery:
Battery compartment is located on back of remote, to open:
• Squeeze and hold the "release" tab while gently pulling out the
battery door.
• Insert (1) 3V battery
• Gently push battery door closed.
Keypad Features:
a) 1 on/off = Power Button (all LED lights)
b) 2 on/off = Power Button (blue LEDs only)
c) + / - = Allows manual dimming of the white or blue LEDs* (either
together or separately)
Dimming Pre-selects:
d) Press any of these 4 buttons to select dimming intensity in increments
of 25%. *
* For both manual dimming and dimming pre-selects, once dimming intensity level is chosen it will
Note:
remain fixed at that level, even if fixture is turned off. To change the intensity level it is necessary to
manually press the button(s).
MAINTENANCE:
For maximum LED performance, it is recommended that the fixture and the LED lens be cleaned on a
weekly basis. Unplug transformer prior to cleaning the light fixture and remove from aquarium. Use both
hands when manipulating this appliance. Wipe exposed surfaces carefully with a damp cloth to remove
any dust or mineral deposits that may collect over time. Do not use detergents or harsh cleaners as it
can damage the light fixture. Use Fluval LED Lens Cleaning Non-Aerosol Spray (A3969) to clean the LED
portion of the light fixture. Make sure all surfaces are dry before re-connecting the transformer to the
power source.
BASIC TROUBLE-SHOOTING:
If the fixture does not work, ensure that all plugs and wires are firmly connected, ie: connection from
fixture to transformer,and connection from transformer to electrical outlet.
FLUVAL ECO BRIGHT LED STRIP LIGHTS
ART. # SIZE
13586 18"- 24" (45 cm-61 cm)
13587 24" – 36" (61 cm – 91cm)
13588 36" – 48" (91 cm – 122 cm)
13589 48" – 60"(122 cm – 153 cm)
AVAILABLE SEPARATELY
Fluval Dual Ramp Timer (A3977)
• Programmable, progressive sunrise, mid-day
and dusk settings
• Controls up to 2 light units simultaneously
a
b
c
d
LEDS LUMENS WATTAGE
24 600 7 W
30 800 9 W
35 1100 14 W
48 1300 18 W
• Integrated dimmer
• Compatible with most Fluval LED Strip Lights