Eagletone TINYCONTROL Manuel D'utilisation page 4

Left Value [0...127]
Specifies the value of the control change message transmitted
when you turn the knob all the way to the left.
Right Value [0...127]
Specifies the value of the control change message transmitted
when you turn the knob all the way to the right.
Sliders
Operating a slider will transmit a control change message. You can
enable/disable each slider, specify its control change number, and
specify the values transmitted when the slider is moved fully upward
or fully downward.
Slider Enable [Disable / Enable]
Enables or disables the slider. If you've disabled a slider, moving it
will not transmit a MIDI message.
Control Change Number [0...127]
Specifies the control change number of the control change
message that is transmitted.
Upper Value [0...127]
Specifies the value of the control change message transmitted
when you move the slider all the way upward.
Lower Value [0...127]
Specifies the value of the control change message transmitted
when you move the slider all the way downward.
Assignables buttons
The button transmits a control change message. You can choose
whether this button will be enabled, the type of button operation, the
control change number, and the values that will be transmitted
when the button is pressed. These MIDI messages are transmitted
on the Global MIDI Channel.
Assign Type [No Assign/Note/Control Change]
Specifies the type of message that will be assigned to the button.
You can disable the button (no assignment), or assign a note
message or a control change.
Button Behavior [Momentary/Toggle]
Selects one of the following two modes:
Momentary: Pressing the button will send a control change mes-
sage with the On value, releasing the button will send a control
change message with the Off value.
Toggle: Each time that you press the button, the control change
message will alternate between the On value and the Off value.
Note number [C-1...G9]
Specifies the note number of the note message that is transmitted.
Control Change Number [0...127]
Specifies the CC number of the control change message that will be
transmitted.
On Value [0...127]
Specifies the On value of the control change or note on message.
Off Value [0...127]
Specifies the Off value of the control change message. You can set
this only if the assign type is "Control Change".
Transport buttons
Operating the transport buttons will transmit either control change
messages or MMC messages, depending on the assign type. For
each of these six buttons, you can specify the message that is
assigned, the way in which the button will operate when pressed,
the control change number, or an MMC command.
Assign Type [Control Change/MMC/No Assign]
Specifies the type of message assigned to the transport button. You
can specify that the button be disabled, or assign a control change
message or MMC message.
Button Behavior [Momentary/Toggle]
Selects one of two types of behavior for the button.
Momentary: A control change message with a value of 127 will be
transmitted when you press the transport button, and with a value of
0 when you release the button.
Toggle: Each time you press the transport button, a control change
message with a value of 127 or 0 will be transmitted alternately.
You cannot specify the button behavior if the assign type is "MMC".
If you have specified "MMC", an MMC command will be transmitted
each time you press the button.
TINYCONTROL
Control Change Number [0...127]
Specifies the control change number of the control change
message that is transmitted.
MMC Command [Stop/Play.../MMC Reset]
Selects one of the following thirteen types of MMC command as the
MMC message that will be transmitted. Stop, Play, Deferred Play,
Fast Forward, Rewind, Record Strobe, Record Exit, Record Pause,
Pause, Eject, Chase, Command Error Reset, MMC Reset.
MMC Device ID [0...127]
Specifies the device ID of the MMC message. Normally you will
specify 127. If the device ID is 127, all devices will receive the MMC
message.
S
PECIFICATIONS
• Connectors: USB connector (mini B type)
• Power supply: USB bus power mode
• Current consumption: 100 mA or less
• Dimensions (W x D x H): 12.6 x 3.3 x 0.6 inches320 x 83 x 14 mm
• Weight: 7.1 oz / 220 g
• Included items: USB cable, owner's manual
• Specifications and appearance are subject to change without
notice.