Product Familiarisation; Intended Use; Unpacking Your Tool - SilverCrest 196536 Mode D'emploi

Masquer les pouces

Table Des Matières

Table des Matières

Les langues disponibles

Additional Safety Instructions for

Pneumatic Tools

Air under pressure can cause severe injury:

• Always shut off air supply, drain hose of air pressure and disconnect tool

from air supply when not in use, before changing accessories or when

making repairs

• Never direct air at yourself or anyone else

• Whipping hoses can cause severe injury. Always check for damaged or

loose hoses and fittings

• Whenever universal twist couplings (claw couplings) are used, lock

pins should be installed and whipcheck safety cables should be used

to safeguard against possible hose-to-tool or hose-to-hose connection

failure

• Do not exceed the maximum air pressure stated on the tool

• Never carry an air tool by the hose

Spray Gun Safety

Dangerous environment

• Ensure there is adequate clear space around the work area. Only use

spraying tools in a well-ventilated area or a specialist spray booth. Be

aware that air hoses can present a trip hazard; always lay hoses in a way

that minimises hazards.

Protect your eyes

• Always wear safety goggles or safety glasses.

Protect your hearing

• Always wear ear protection.

Protection from vibration

• Hand-held air tools may produce vibration and should not be used for

long periods without a break. Vibration can cause disease. Gloves may

help to maintain good blood circulation in the fingers.

Protective equipment

• Always wear appropriate protective equipment including but not limited

to overalls, gloves, facemask etc.

• It is the user's responsibility to ensure that other persons in the vicinity

of the work area are also equipped with the appropriate protective

equipment.

Use the correct air hose

• Use lightweight hose to connect the tool to the air compressor.

• Air should be supplied by a suitable length of 8mm (5/16") diameter

air hose fitted with a female 1/4" NPS connection at gun end. For hose

lengths over 15m (50'), use 9.5mm (3/8") diameter hose.

• When spraying, ensure that the gun is connected to a clean, filtered air

supply.

Always disconnect

• Ensure that your air tool has completely stopped functioning before

putting it down.

• Disconnect an air tool from the air supply before performing any

servicing or refilling

• Ensure the air tool is switched OFF before connecting to air supply. Be

aware that air tools may hold residual pressure after use. Always bleed

air pressure from the tool after shutting off air supply.

Do not abuse the tool

• Do not increase air pressure above the recommended level; excessive

pressure leads to wear of moving parts, possible failure and may cause

the tool casing to split.

• Do not attempt to modify air tools. Any attempt to modify this air tool

could result in serious injury to you or others, and will invalidate its

warranty.

Use of spray guns

• Do not aim a spray gun at people or animals!

• When spraying keep away from heat and naked flames!

WARNING: Solvents and paints are harmful and can even be toxic. Some

solvents and paints are extremely flammable. Handle with care, according

to the manufacturer's recommendations. Store solvents and paint in sealed,

leak proof containers made of a material that is chemically resistant to the

specific solvent. Always wear suitable protective equipment and dispose

of solvents and paints, as well as contaminated items, as special waste,

according to laws and regulations.

WARNING: Solvents that are chemically based on halogenated hydrocarbon,

like trichloroethane and methylene chloride 1,1,1, may cause chemical

reactions in combination with aluminium and galvanised or hot galvanised

components, and may therefore represent a potential explosion hazard.

WARNING: When spraying coating materials, dangerous vapours or

aerosols, which are detrimental to your health, are produced. Please

read all labels and safety instructions carefully, and observe all indicated

instructions and recommendations. In case of doubt, please ask the

material supplier. Use respiratory protection when spraying. The respiratory

equipment used must be suitable for the material in use and adapted to the

degree of the vapour concentration. When spraying paint, use respiratory

equipment independent of the ambient atmosphere, or equipment with filter

combination A1/A2-P2. Ensure a sufficient protection of your skin during all

spraying and cleaning procedures. Wear appropriate protective clothes and

use suitable protective skin ointments.

WARNING: DO NOT spray acids, caustic solutions, removers and similar

substances.