Télécharger Imprimer la page

Noise Risk - IMER C 350 i-Power Manuel D'utilisation Et D'entretien Et Pièces De Rechange

Publicité

Les langues disponibles

Les langues disponibles

equipment at the end of its service life. The user must therefore
latter for separate scrapping of the equipment at the end of its
service life.
for the environment and for the health of persons, and promotes
the reuse/recycling of the materials of which the equipment is
Although the sawing machine has been manufactured fully in compliance
with current regulations, residual risks exist that cannot be eliminated
and involve the use of appropriate individual protection devices. The
machine is equipped with notices to indicate the residual risks and how
to avoid them.

NOISE RISK

Please be reminded that checking the use of IPDs is delegated to the
employer.
IMER INTERNATIONAL S.p.A.
C 350 iPower
The motor does not
start when the start
switch is pressed
.
Cooling water fails
to reach the blade
The blade does
not cut
* Operation to be carried out by an electrician
Grinding/cutting/drilling of masonry, concrete, metal and other materials with
silica in their composition my give off dut or mists cintainig crystalline silica.
Silica is a basic component of sand, quartz, brick clay, granite and numerous
other minerals and rocks. Repeated and/or substantial inhalation of airborne
crystalline silica can cause serious or fatal respiratory diseases, including sili-
cosis. In addition, California and some other authorities have listed respirable
crystallinesilica as a substance known to cause cancer. Whwn cutting such
materials, always follow respiratory precautions.
Use appropriate NIOSH-approved respiratory protection where dust hazard
may occur. Paper masks or surgical masks without a NIOSH approval number
are not recommended because they do little to protect the worker. For more
information about respirator programs, including what respirators have recei-
ved NIOSH approval as safe and effective, please visit the NIOSH website at:
http://www.cdc.gov/niosh/topics/respirators
Observe OSHA regulations for respirator use (29 C:F.R. § 1910.134).
Visit http://www.osha.gov for more information.
Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities contain chemicals know (to the State of California) to
cause cancer, birth defects or other reproductive harm. Some examples of
these chemicals are:
-Lead, from lead-based paints
-Crystalline silica, from bricks and cement and other masonry products
-Arsenic and chromium, from chemically treated lumber
For further information , consult the following sources:
http://www.osha.gov/dsg/topics/silicacrystalline/index.html
http://www.cdc.gov/niosh/docs/96-112/
http://oehha.ca.gov/prop65/law/P65law72003.html
http://www.dir.ca.gov/Title8/sub4.html
http://www.P65warnings.ca.gov
Your risk from these exposures varies depending on how often you do this
typer of work. To reduce your exposure to these chemicals, work in a well-
ventilated area, and work with approved safety equipment, such as dust ma-
a dust extraction device is possible, it should be used. To achieve a high level
oof dust collection, use an industrial HEPA vacuum cleaner. Observe OSHA
29 CFR part 1926.57 and 1926.103
13
Trouble
Causes
Current does not reach
the supply line
The socket and plug
are not connected
properly
The differential switch
is off
The power cable from
the plug to the panel
is cut off
An electric wire inside
the motor terminal strip
is cut off
An electric wire inside
the panel is cut off
The start switch is
faulty
Low water level in tank Restore the water level
Current fails to reach
the pump
Pump failure
opposite direction to
that of rotation
Worn blade
GB
Remedies
Check the line *
Restore correct
connection
Turn the differential
switch on
Change the cable *
Restore the connection *
Change the switch *
Change the switch *
Check the pump
electrical supply *
Change the pump *
Remove the blade
and reposition it in the
direction shown on the
blade label
Change the blade

Publicité

loading