Operation - Hart HPRC01 Manuel D'utilisation

OPERATION

INSTALLING/REMOVING BATTERY PACK
See Figure 1, page 9.
To install:
 Remove the four cotter pins that secure the truck body
to the frame.
WARNING:
CHOKING HAZARD. Small parts. Keep out of the reach
of children. Adult supervision required.
 Remove the truck body and set aside.
 Make sure the latches on each side of the battery pack
snap into place and the battery pack is secured in the
product before replacing the truck body and beginning
operation.
 Set the truck body onto the frame. Insert the cotter pins
and make sure the body is securely installed.
To remove:
 Remove the four cotter pins that fasten the truck body
to the frame.
WARNING:
CHOKING HAZARD. Small parts. Keep out of the reach
of children. Adult supervision required.
 Remove the truck body and set aside.
WARNING:
HOT PARTS. Electric motor and other vehicle parts can
cause burns after vehicle operation. Allow time to cool
before touching motor area and other parts.
 Depress the latches to remove the battery pack.
 Set the truck body onto the frame. Insert the cotter pins
and make sure the body is securely installed.
For complete charging instructions, see the operator's man-
uals for your battery pack and charger.
ON/OFF SWITCHES
See Figure 2, page 9.
Both the truck and controller have an ON/OFF switch.
The controller switch is located on its handle. The controller's
LED glows when it is turned ON.
The truck ON/OFF switch is located on the underside of
the truck.
Always turn both switches to the OFF position before remov-
ing or changing batteries, or when the truck is not in use.
USING THE CONTROLLER
See Figures 3 - 4, page 10.
The controller is powered by 2 AAA batteries. You will need
to install the 2 AAA batteries before using the controller.
Always turn the switches for the truck and the controller to
the OFF position when installing the battery in the controller.
 Using a Phillips screwdriver, loosen screw holding the
battery compartment cover in place.
 Lift the tab to remove the battery cover from the controller.
 Install 2 AAA batteries according to polarity indicators
(+ or –) inside the battery compartment.
 Replace and secure the battery cover.
When there is a charged battery pack in the truck and the
ON/OFF switch is in the ON position, turning the controller
ON will allow it to pair with the truck. You may then use the
controller to drive and steer the truck.
NOTE: To pair a second truck and controller, turn the second
truck switch ON and then turn the second controller switch
ON. Repeat this sequence for each additional vehicle. The
truck will pair with the nearest controller when it is turned on.
If the truck becomes difficult to control, the AAA batteries
may need to be replaced.
STEERING TRIM ADJUSTMENT
See Figure 3, page 10.
Before pulling the throttle trigger, check the steering trim.
The wheels should be directed straight ahead, to prevent
the truck from veering to the left or right when the throttle
trigger is pulled.
Steering trim should be checked and adjusted periodically
for maximum performance and control.
The steering trim can be adjusted if the truck veers to the
left or right when you are driving it straight ahead.
Set the truck on a box or block so that the wheels do not
touch the ground. Do not touch the wheels while you are
making adjustments.
 If the truck is veering to the left: turn the trim adjuster
to the right.
 If the truck is veering to the right: turn the trim adjuster
to the left.
VARIABLE SPEED THROTTLE TRIGGER
See Figure 3, page 10.
The variable speed throttle trigger controls the speed of the
truck and forward/reverse function. The more you pull or
push the trigger, the more you increase speed.
 To drive forward: pull the throttle trigger back.
 To brake: push the throttle trigger forward.
 To drive in reverse: push the throttle trigger forward.
STEERING WHEEL
See Figure 3, page 10.
The steering wheel turns the truck right or left. The further
you turn the wheel, the sharper the truck will turn.
Release the wheel to go straight.
6 — English