Specific Safety Rules And Symbols - Metabo HPT CV 350V Instructions De Sécurité Et Mode D'emploi

5. Setting up and checking the work environment.
Check if the work environment is suitable by following
the precaution.
6. Dust particles such as silica or asbestos are
hazardous to your health. When working with
materials containing these components, take
appropriate dust-proofi ng measures.
7. Working with metal can cause sparks. Make sure
there are no fl ammable and combustible materials in
the vicinity and that they are stored in a safe location.
8. The motor may stop in the event the tool is overloaded.
In this should occur, release the tool's switch and
eliminate the cause of the overload.
9. Do not touch the application tool, its attachment area
or other metal surfaces immediately after use as they
will be hot. Doing so may result in burns or injury.
The metal is hot and can easily burn your skin.
10. Make sure that there is no one below when operating
the tool in high locations. Dropping the tool or
materials may result in accident or injury.
11. Never apply any unreasonable force to the application
tool when working. Doing so may break the application
tool or damage the motor.
12. Do not leave the tool running unattended on the fl oor,
table or other locations. Doing so may result in injury.
13. When attaching application tools, be careful not to get
your fi ngers or other extremities caught in the lever.
14. If the application tool seems to be loose or uneven
after attaching it to the unit, re-attach the tool.
Operating the unit with a loose or uneven application
tool may result in injury.
15. When switching on the tool, make sure the application
tool is not in contact with any processing materials.
Failure to do so may result in injury.
16. For cutting effi ciency, switch the mode of the
application tool according to task conditions and
materials to be cut.
17. After use, be sure not to place the tool near chips or
sawdust before it comes to a full stop as the tool may
suck in those particles.
18. Do not polish wood with sanding paper used for metal
polishing.
19. Do not use worn or clogged sanding paper.

SPECIFIC SAFETY RULES AND SYMBOLS

1. Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord.
Cutting accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and could
give the operator an electric shock.
2. Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body leaves
it unstable and may lead to loss of control.
3. ALWAYS wear ear protectors when using the tool
for extended periods.
Prolonged exposure to high intensity noise
can cause hearing loss.
4. NEVER touch the application tool with bare hands
after operation.
5. When working at elevated locations, clear the area
of all other people and be aware of conditions below
you.
6. NEVER touch moving parts.
NEVER place your hands, fi ngers or other
body parts near the tool's moving parts.
7. NEVER operate without all guards in place.
NEVER operate this tool without all guards or safety
features in place and in proper working order. If
maintenance or servicing requires the removal of a
guard or safety feature, be sure to replace the guard
or safety feature before resuming operation of the
tool.
8. Use right tool.
Don't force small tool or attachment to do the job of a
heavy-duty tool.
Don't use tool for purpose not intended —for
example— don't use oscillating multi tool for cutting
tree limbs or logs.
9. NEVER use a power tool for applications other
than those specifi ed.
NEVER use a power tool for applications other than
those specifi ed in the Instruction Manual.
10. Handle tool correctly.
Operate the tool according to the instructions
provided herein. Do not drop or throw the tool.
NEVER allow the tool to be operated by children,
individuals unfamiliar with its operation or
unauthorized personnel.
11. Keep all screws, bolts and covers tightly in place.
Keep all screws, bolts, and plates tightly mounted.
Check their condition periodically.
12. Do not use power tools if the plastic housing or
handle is cracked.
Cracks in the tool's housing or handle can lead to
electric shock. Such tools should not be used until
repaired.
13. Application tools and accessories must be
securely mounted to the tool.
Prevent potential injuries to yourself or others.
Application tools, cutting implements and accessories
which have been mounted to the tool should be
secure and tight.
English
5