Standard Accessories; Applications; Assembling The Back Pack Power Supply - Hitachi BL 36200 Mode D'emploi

English
CAUTION
1. In the event of liquid leaking from the Back Pack Power
Supply entering the eye, rinse it thoroughly with clean
water without rubbing it, and then contact your doctor
immediately.
Leaving it unattended may result in damage to the eye.
2. In the event of liquid leaking from the Back Pack Power
Supply coming into contact with skin or clothes, rinse it
thoroughly with clean water.
Leaving it unattended may result in skin irritation.
SPECIFICATIONS
BACK PACK POWER SUPPLY
Model
Battery capacity
Output voltage
Adapter output
Maximum output current
Output voltage
USB output terminal
Maximum output current
Operating temperature range
Adapter cable length
Large-capacity power dimensions
Large-capacity power
Weight Power adapter
Carrier
CHARGER
Model
Recharging time
(at an ambient temperature of 20°C)
Recharge voltage
Weight

STANDARD ACCESSORIES

1 Carrier .......................................................................... 1
2 Recharger: UC36YRSL (with instruction manual) ....... 1
3 Adapter ......................................................................... 1
4 Arm band ...................................................................... 1
5 Knob bolt ...................................................................... 2
6 M5 screws .................................................................... 4
Standard accessories are subject to change without notice.

APPLICATIONS

○ Power Supply for Hitachi Cordless Power Tools (DC36V)
○ Power Supply for USB-Connection Equipment (DC5V).
ASSEMBLING THE BACK PACK POWER
SUPPLY
1. The large-capacity power output cable can be
withdrawn from either side.
Decide on the best side for operations, and then insert
the output cable into the cable groove.
The direction of the cable can be easily amended after
it has been set in position. (Fig. 1)
10
3. In the event of rust, foul odors, overheating or other
abnormalities being apparent when using the Back
Pack Power Supply for the fi rst time after purchase,
contact your dealer or Hitachi Authorized Service
Center without using it.
4. Store the Back Pack Power Supply in a location out of
reach of children.
5. Use the Back Pack Power Supply in accordance with
the displayed specifi cations.
BL36200
Li-ion DC 36 V 21 Ah (21000 mAh) 80 cells
DC 36 V
DC 5 V
0°C – 40°C
330 mm × 250 mm × 109 mm
6.3 kg
0.5 kg
1.0 kg
UC36YRSL
BSL3620: Approximately 60 minutes
BSL3626: Approximately 80 minutes
BL36200: Approximately 10 hours
14.4 V – 36 V
0.7 kg
2. Attach the carrier to the large-capacity power supply
with the four M5 screws supplied with the use of a
Phillips screwdriver.
Tighten the two knob bolts by hand to stabilize the
position of the output cable.
The knob bolts can be removed by hand so that the
direction of the output cable can easily be changed at
any time. (Fig. 2)
3. Pass the carrier strap through the attachment hole on
the large-capacity power supply from the back, and fi x
it in place in two locations as shown in the illustration.
(Fig. 3)
CAUTION
Check to make sure the M5 screws and knob bolts
for attaching the carrier are not loose. Also check to
confi rm that the carrier strap has been fi rmly attached.
Failure to observe this may result in the Back Pack
Power Supply being dropped, leading to injury or
damage.
4. Pass the switch panel through the rear of the accessory
box and store it in the panel case. (Fig. 4)
5. Align the power connector and adapter connector with
the respective
rotate the rings to secure them. (Fig. 5)
6. If the cable gets in the way, adjust its position with the
waist band or Velcro band. (Fig. 6)
50 A
0.5 A
1.5 m
marks, push them into place and