Publicité
Les langues disponibles
Les langues disponibles
GUN SPECIFICATIONS
MODEL OF GUN ........................................................ CS 15M
GUN LENGTH .................................................................. 7.9" (200.6 mm)
GUN HEIGHT ................................................................ 5.75" (146 mm)
GUN WIDTH ............................................................................ 1.62" (41.2 mm)
WEIGHT (WITHOUT FASTENERS) .................................... 1.23 lbs (0.56 kgs)
Warning:
This manual gun is designed to fix the 15mm Flexipoints in frames to secure artwork and
images. Its well-balanced, ergonomic, comfortable and non-slip padded handle
guarantees you a satisfying handling and pleasant work.
Suitable applications:
Fixing the back in picture framing.
Caution:
This gun is not suitable for use into metal. Do not use the gun if points are jammed inside
it. This could damage internal parts of the gun.
Cassese highly recommends using exclusively the genuine Cassese consumables in this
gun. Using incompatible consumables could cause damage to the gun and void the
warranty.
In this manual:
DANGER
Indicates an imminently hazardous situation which, if not avoided, will result in
death or serious injury.
WARNING
Indicates a potentially hazardous situation which, if not avoided, will result in death
or serious injury.
NOTE
Alerts the operator to useful information.
SAFETY INSTRUCTIONS
1. Read this manual and understand all safety instructions before operation the gun. If
you have any questions, please contact our authorized representatives.
2. Only those flexipoints listed in the operating instructions may be used in the guns.
3. For the maintenance of the guns, only spare parts specified by the manufacturer or
his authorized representative shall be used.
4. Repairs shall carried out by agents authorized by the manufacturer or by other
specialists, having due regard to the information given in the operating
instruction.
5. Supports for mounting the frames, such as a working table, shall be
designed and constructed by the support manufacturer in such a way
that the gun can be used safely.
6. Wear eye protection
7. Never point tool at yourself or at any other
person
WARNING
LOADING THE GUN
OPERATING THE GUN
5.
TROUBLESHOOTING
Stop using the tool immediately if any of the following problems occur. Serious personal
injury could. Any repairs or replacements must be done by a qualified person or an
authorized service center only
PROBLEM
PROBABLE CAUSE
Tool does not
The plate in the trigger is worn out.
drive tab.
The gap between guide plate and
Tool drives two
tongue is too big.
tabs at the same
time.
The tab specification is not correct.
Dirt in nose.
Dirt or damage prevents fasteners
Tool skips driving
form moving freely in magazine.
fastener.
Worn pusher spring.
Driver nozzle worn or damaged.
Driver is damaged.
Fasteners are
Fasteners are not correct size.
jammed in tool.
Fasteners are bent.
Magazine or nose screws are loose.
Do not point the gun to wards yourself or anyone
nearby
1. Press the latch by thumb, and then pull up the
pusher assembly to the most top position..
2. Place the staples in the magazine with point end
staples face toward the nose. Also ensuring
fasteners are not dirty or damaged.
3. Push down the pusher assembly, and lock by
latch.
WARNING
Protect your eyes and ears. Wear safety glasses with
side shields. Wear hearing protection. Employers and
users are responsible for ensuring the user or anyone
near the gun wear this safety protection.
NOTE
Check and replace any damaged or worn components
on the gun. The safety warning labels on the gun
must also be replaced if they are not legible.
Hold the gun against the box.
Press the manual tacker hardly against the working
target, and squeeze the trigger.
REMEDY
replace the worn part with new
plate.
replace the WRH0701 guide plate or
tongue
change the tabs with correct
specification.
Clean.
Magazine needs to be cleaned.
Pusher spring needs to be replaced.
Replace driver nozzle.
Replace driver.
Fasteners recommended for tool
must be used.
Replace with undamaged fastener.
Screws need to be tightened.
Publicité
