Nintendo Wii Speak Mode D'emploi page 2

Usage guidelines
Before using the Wii Speak accessory, please read and follow the guidelines below for proper
installation and operation.
• This accessory connects to a USB connector on the back of the Wii console. Do not connect
this accessory to any other device.
• Be sure the power of the Wii console is turned OFF when connecting or disconnecting this
accessory.
• To avoid audio feedback or other audio interference, do not place the microphone near
audio speakers or sources of air flow such as fans or air conditioners.
• Do not handle the microphone during use.
• Speak at a normal volume during use.
• Stay between 3'–9' (1–3 meters) from the microphone during use.
• Be sure and review the manual for the game you are playing or the Wii Channel you are
using for specific information on how to use Wii Speak with that game.
Components
2
Placing the Microphone
The microphone works best when placed on top of the television. The installation will vary depending
on whether your Sensor Bar is located on top of or underneath your television, as described below.
If your Sensor Bar is on top of the TV
1. Remove the liners from the anti-slip pads on
the bottom of the microphone. Be careful not
to remove the anti-slip pads.
2. Line up the rib on the the bottom of the
microphone with groove in the top of the
Sensor Bar and place the microphone on as
shown at right.
• The Sensor Bar and Wii microphone should be
centered on the top of and aligned with the front
of the television.
• Make sure the microphone is visible from the
front of the television and that nothing is
blocking the microphone.
NOTE: For a more secure attachment, see the
information at bottom of the next page.
4
USB plug
Connects to a USB
connector on the back
of the Wii console.
LED
Lights blue when communication
feature is active.
Microphone
Anti-slip pads
Peel off protective liner before use.
Sensor Bar rib
If the microphone is installed on top of the
Sensor Bar, line this up with the groove in
the top of the Sensor Bar.
Sensor
Bar located
on top
Line up
rib with
groove
Connecting the Wii Speak accessory
1. Turn the power off on the Wii console before
installing or removing the Wii Speak accessory
(the Power LED will appear either red or orange
when the power is turned off).
2. Insert the USB plug from the Wii Speak accessory
straight into one of the USB connectors on the
back of the Wii console.
IMPORTANT: Inspect the USB connector for dust
or other foreign material before plugging this
accessory into it. Clean it with a soft, dry cloth if
necessary.
3. To disconnect this accessory, turn the power off on the Wii console and pull the USB plug straight
out of the USB connector. Be sure to hold onto the plug and do not pull on the cable.
NOTE: If you are using more than two USB devices at the same time, you must use a USB hub
that has its own power supply that plugs into a standard AC wall outlet. Do not use a USB
hub that is powered by one of the devices connected to it. Some USB devices must be
plugged directly into a USB connector on the back of the Wii console. For details, refer to the
instruction booklet for your USB device.
IMPORTANT: To avoid possible damage to your Wii console, use only a USB hub recommended
by Nintendo.
• For a list of approved USB hubs, visit support.nintendo.com.
If your Sensor Bar is underneath
the TV
1. Add the additional anti-slip pads included with
the Wii Speak accessory to the bottom of the
microphone as shown at right.
2. Remove the liners from the anti-slip pads on the
bottom of the microphone. Be careful not to
remove the anti-slip pads.
3. Place the microphone on the top of the
television as shown at right.
• The microphone should be centered on the top
of and aligned with the front of the television.
• Make sure the microphone is visible from the
front of the television and that nothing is
blocking the microphone.
• Keep the microphone as far away from audio
speakers as possible.
NOTE: For a more secure attachment, see the information below.
For more secure attachment:
Included with the Wii Speak accessory are double
sided adhesive pads (attached to the yellow carrier
sheet) that can be attached to the bottom of the
microphone.
See step 1 one on the previous page and use the
adhesive pads instead of the anti-slip pads.
Power LED
is red or orange
when power
is off
3
Sensor
Bar located
underneath
5