Pro-Line II 92555 Instructions De Montage

7
11
15
9R
6
10
13
10
12
4
3
1
Enlever toutes les pièces du carton, les organiser selon les numéros de pièce indiqués sur la liste et vous assurer que les
quantités des pièces sont correctes.
ÉTAPE 1 Insérer cinq roulettes (2) dans la base (1), les pousser très fort jusqu'à ce que vous entendiez ou sentiez la roulette (2) s'enclencher.
Insérer le vérin pneumatique (3) dans la base (1) et glisser les soufflets (4) sur le vérin pneumatique (3).
ÉTAPE 2 Fixer le mécanisme (5) au coussin du siège (6) avec quatre vis du mécanisme (10). SERREZ TOUTES LES VIS DU MÉCANISME (10).
ÉTAPE 3 Fixer les bras (9L et 9R) au coussin du siège (6) en utilisant un bouton de réglage avec rondelle (13) pour chaque bras (9).
SERREZ TOUTES LES BOUTONS DE RÉGLAGE (13).
ÉTAPE 4 Fixer le support du dossier (15) à l'arrière du coussin de siège (6) à l'aide de trois vis de support de dossier avec rondelles (12). SERREZ TOUTES
LES VIS DE SUPPORT DE DOSSIER (12). Fixez le dossier (7) au support de dossier (15) à l'aide d'une vis du dossier (11). SERREZ TOUTES LES
VIS DU DOSSIER (11). Fixez le couverture
de support du dossier (8) au dossier (7) avec duex vis de couverture de dossier (14) comme indiqué dans le détail A.
SERREZ TOUTES LES VIS DE COUVERTURE DE DOSSIER (14).
ÉTAPE 5 Placer le siège assemblé sur le vérin pneumatique (3) et mettre de la pression.
ATTENTION : AVANT D'UTILISER LE FAUTEUIL, VOUS ASSURER D'AVOIR RESSERRÉ COMPLÈTEMENT TOUTES
LES VIS ET BOUTONS.
92555
FAUTEUIL DE DIRECTION
INSTRUCTIONS DE MONTAGE
DÉTAIL A
14
8
9L
13
PIÈCE
1. Base . . . . . . . . . . . . . . . . . . . . . . . 1
2. Roulettes . . . . . . . . . . . . . . . . . . . . 5
3. Vérin pneumatique . . . . . . . . . . . . 1
4. Soufflet . . . . . . . . . . . . . . . . . . . . . 1
5. Mécanisme . . . . . . . . . . . . . . . . . . 1
6. Coussin du siège . . . . . . . . . . . . . . 1
7. Dossier . . . . . . . . . . . . . . . . . . . . . 1
8. Couverture de support de dossier . 1
9. Bras (9L et 9R) . . . . . . . . . . . . . . . 2
10. Vis du mécanisme . . . . . . . . . . . . 4
11. Vis pour le dossier . . . . . . . . . . . . 1
12. Vis support dossier avec rondelle 3
13. Bouton de réglage avec rondelle . 2
2
14. Vis de couverture de dossier . . . . 2
15. Support du dossier . . . . . . . . . . . 1
16. Clé Allen (non montré) . . . . . . . . . 1
3
1
QTÉ
PROLINE II LIMITED WARRANTY
ProLine II chairs are warranted from the date of purchase against failure due to material and workmanship as follows:
• Lifetime on component parts including pneumatic cylinder, control mechanism, base and casters.
• 3 Years on upholstery fabric and foam against wear and deterioration.
• Leather is not warranted against routine scratching and scuffing, as leather is subject to minor blemishes in use.
To make a warranty claim, contact Parts Department. Provide model number, proof of purchase, description of the problem and obtain return authorization.
At it's option Office Star Products will:
(a) Supply compatible components of current manufacture.
(b) Repair the customer's component. The customer must prepay freight on any components returned to the factory. Return freight on components
still in warranty will be paid by Office Star Products.
*All warranties are limited to the original purchaser for normal commercial usage defined as a standard forty hour work week by persons weighing 250 lbs.
or less. The 54666 is for persons weighing 300 lbs. or less. The 39200, 39202, 39203, 81108, 81308 & 81608 are for persons weighing 400 lbs. or less.
This warranty will not cover labor, freight or damage from misuse, abuse, negligence, alteration, accident, vandalism, rusting, acts of nature or any other
event beyond the control of Office Star Products. The warranty does not cover cosmetic damage that may result from normal use. Liability for incidental or
consequential damages is excluded. The user assumes all risk of injury resulting from use of this product. When usage is more than 40 hours per week, a five
year warranty on all parts applies. Fabric is warranted for one year. This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state.
All ProLine II chairs meet or exceed ANSI BIFMA standards.
It is the customer's responsibility to prepay freight on any components returned to the factory. Return freight on components covered by warranty
will be paid by Office Star Products.
Our quality standards are among the highest in the industry. Sometimes, no matter how hard we try, there are times when parts are damaged or missing. Our
Parts Department will do everything possible to promptly remedy the problem. Contact us via e-mail parts@officestar.net, by Fax 1-909-930-5629, or toll free
parts number 1-800-950-7262, Monday through Friday 8:00 a.m. - 5:00 p.m. Pacific Time.
© Office Star Products août 2019
92555
MANAGER'S CHAIR
OPERATING INSTRUCTIONS
FEATURES
• PNEUMATIC SEAT HEIGHT ADJUSTMENT
To raise seat remove pressure from seat and lift lever (1) up.
To lower seat height sit on chair and lift lever (1) up.
NOTE: It is normal for chair to slightly lower under body weight.
• BACK TILT ADJUSTMENT
To tilt backrest, pull lever (1) out. To lock chair into position, push
lever (1) in.
• TILT TENSION ADJUSTMENT
To adjust title tension, Turn knob (2) clockwise to increase tension
and counter-clockwise to decrease or ease the tension.
NOTE: Be careful not to completely loosen knob (2).
• ARM HEIGHT ADJUSTMENT
To adjust arm height, push button (3) in to allow the arms to move up or
down freely. Release the button (3) once the desired height is reached.
2
WARNING
1. Use this product only one person at a time.
2. Do not use this chair unless all bolts screws and knobs are securely
tightened.
3. Check that all bolts screws and knobs are tight every three months
or as needed.
4. Do not overturn back tilt knob when decreasing tension.
5. Dispose of packing material properly. Do not use plastic cover as
head covering. It may cause suffocation.
6. Do not use chair as a stepladder.
7. Use this chair for its intended purpose only.
8. Use mild detergent only for cleaning.