Publicité

Liens rapides

OTT-JAKOB Spanntechnik GmbH

Publicité

Table des Matières
loading

Sommaire des Matières pour OTT-JAKOB POWER CHECK 2

  • Page 1 OTT-JAKOB Spanntechnik GmbH...
  • Page 2 TABLE DES MATIÈRES // 2...
  • Page 3 // 3...
  • Page 4 Li-Ion 204-360001 5V DC 500mA Made in Germany // 4...
  • Page 5: Consignes De Sécurité

    1 CONSIGNES DE SÉCURITÉ 1.1 UTILISATION CONFORME // 5...
  • Page 6: Description Du Produit

    2 DESCRIPTION DU PRODUIT 2.1 FONCTIONNEMENT Adaptateur pour cônes Affichage ISO, HSK et PSC Interface (à l'intérieur) return clear stack Reset (à l'intérieur) Champ de commande // 6...
  • Page 7: Dimensions

    2.2 DIMENSIONS Appareil de base 5, 20, 75 kN Appareil de base 24,5 200 kN 2.3 CARACTÉRISTIQUES // 7...
  • Page 8 cote effective = cote nominale cote effective > cote nominale cote effective < cote nominale plage de tolérance entre outil et broche plage de réglage Power-Check // 8...
  • Page 9: Caractéristiques Techniques

    2.4 CARACTÉRISTIQUES TECHNIQUES → # 2.5 2.5 RÉFÉRENCES ARTICLES / NOMENCLATURE  // 9...
  • Page 10  // 10...
  • Page 11 26622 26622 26622 26622 26622 26622 // 11...
  • Page 12 26622 26622 26622 // 12...
  • Page 13: Montage Des Adaptateurs

    3 MONTAGE DES ADAPTATEURS 3.1 PRÉPARATIFS 3.2 MONTAGE // 13...
  • Page 14 // 14...
  • Page 15: Mise En Service

    Adaptateur HSK avec rainure de préhension vis de blocage butée   = 0 Nm Cônes ISO avec rainure de préhension 4 MISE EN SERVICE // 15...
  • Page 16: Réglage De Tolérance

    4.1 RÉGLAGE DE TOLÉRANCE ISO 7388 • selon Typ A et B ISO 12164 ISO 26622-1 ISO 26623-1 DIN 2080 • MAS 403 • // 16...
  • Page 17 4.2 CHARGER L'ACCU  return clear stack capuchon // 17...
  • Page 18: Utilisation

    5 UTILISATION 5.1 MODE MANUEL manual config memory bat low clear manual auto clear clear // 18...
  • Page 19: Mode Automatique

    5.2 MODE AUTOMATIQUE manual auto manual auto clear // 19...
  • Page 20 5.3 MODE MESURE EN CONTINU manual auto manual clear auto // 20...
  • Page 21: Valeurs Mesurées

    5.4 VALEURS MESURÉES clear manual auto manual auto // 21...
  • Page 22: Plage De Mesure

    5.5 PLAGE DE MESURE 5.6 ÉTAT DE CHARGEMENT DE L'ACCU // 22...
  • Page 23: Paramétrage

    6 PARAMÉTRAGE clear manual auto clear manual auto clear // 23...
  • Page 24 manual auto // 24...
  • Page 25: Pièce De Rechange

    7 MAINTENANCE 7.1 PIÈCE DE RECHANGE Joint torique return capuchon 7.2 COUPURE EN CAS DE PROBLÈME return clear stack capuchon ône du contact d'arrêt 7.3 ENTRETIEN 7.4 MISE HORS-SERVICE // 25...
  • Page 26 8 LOGICIEL PC 8.1 DESCRIPTION 8.2 INSTALLATION // 26...
  • Page 27 8.3 UTILISATION // 27...
  • Page 28    // 28...
  • Page 29 // 29...

Table des Matières