Table des Matières
Publicité
GB - Getting Started
Make sure that all parts from the box content are included. Trans-
mitter, Car, Charger, battery pack.
Vers. 053270
Charger
Battery
Charging
adapter
The battery pack has to be charged before use. Plug the charger
into a 230V outlet. Connect the charger to the battery. If the plug
of the charger and battery do not match, then you will find a con-
nection lead in your box. The average charging time of the empty
battery is about 6-8 hours.
Place 8 pieces of AA batteries into
the transmitter. If rechargebale, ple-
ase also make sure these are fully
charged.
Read the chapter for usage of the
transmitter and its controls carefully.
Turn the radio off and make sure all the
trim buttons on the transmitter are in
neutral position.
You have purchased a RTR model,
L/R F/B
which means it should be ready for im-
Trim
mediate use after charging all batteries.
On/Off
You need to check the car, electronics
and all plastic parts after each use to
make sure no parts are damaged. Also
all the moving parts must be checked for their clearance, bolts
and screws that they are tight.
Now put the battery into the
battery holder in the vehic-
le. Make sure that the batte-
ry holder is secured proper-
ly with the 2 included clips
for the battery holder. Now
connect the battery to the
speed control in the model.
Keep the car in the air in
case that the motor turns at
full power.
Switch the speed control on the On / Off switch. Set the model on
the ground and test it for proper functioning. Steering right/ left,
throttle/ brake, forward and backward. If the wheels do not point
straight forward even though the steering wheel on the trans-
mitter is in neutral, you can adjust it with the trim button on the
transmitter.
Trim L/R = steering
Trim V/R = forward/backward
Should the wheels rotate forward or backward, even though no
command was given through the transmitter, then also the thrott-
le needs to be trimmed on the transmitter.
We encourage you now to activate your receiver's built-in Fail-
safe unit. On delivery it is turned off.
8
Vers. 053271
Battery
Charger
Battery
ESC
Lipomode
ON/OFF
On/OFF
Leave the throttle lever in neutral position (see chap-
ter Fail Safe). Press the fail-safe button on the re-
ceiver
until
it
flashes
Check this principle in an electric vehicle only in the neutral
position of the throttle, because otherwise the model goes
into the previously programmed throttle position in a loss of
the transmitter signal.
Now you can make the first test drive. If this is your first rc car, we
recommend to drive it on a small test track to familiarise yourself
with the control of the vehicle and the controls of the transmitter.
Attention!
Your vehicle has a pivot front suspension. This has a number of
advantages. It is very robust and easy to maintain. The set-up of
the car has been done so the drive shaft will not pop out. As with
any model, screws and bolts can losen during break-in of the car.
This can result in tolerance of the drive shaft. The drive shaft can
then pop out if high pressure is applied.
The inner ball screw (item No.: 505081) will enable you to adjust
the tolerance resulting in fine adjustments of the track width. For
best results when setting up the pivot ball for the first time, please
always adjust the upper and lower pivot in the same way. Fasten
as far as the pivot can still be pulled up and down easyly but not
as far that it will pop out if you give full steering angle. The outer
plastic socket screw (item No.: 505080) is only used for securing
of the steering knuckle. This should not be too tight, otherwise
the steering is not smooth and the handling can be adversely
affected.
50 5080
and
let
go
to
activate.
50 5081
07 9996
50 5079
Publicité
Table des Matières
