Power Requirements - Altec Lansing inMotion Mode D'emploi

Masquer les pouces Voir aussi pour inMotion:

Mode d'emploi (16 pages)

Table des Matières

Les langues disponibles

OTION

Portable Audio System

Thank you for purchasing this Altec Lansing product. For generations, Altec

Lansing has been first in audio innovation. Today, our line of powered

speakers has received more performance awards than any other brand. In

all kinds of desktop environments, in every price range, Altec Lansing offers

sound of distinction — giving even the most demanding customers the

audio enjoyment they seek. Just listen to this!

Box Contents

• inMotion portable audio system

• Universal Power Supply

• 3.5mm Stereo Cable

• Protective Case

• 10GB/15GB iPod Docking Spacer

• Docking Connector Travel Cover

• Manual

• Quick Connect Card (may be located on internal box flaps)

Placing the inMotion system

Position the inMotion system on a level surface preferably close to you

(within three feet). The inMotion system can be placed close to video

displays such as TVs and computer monitors without distorting the image.

Making Connections

Warning: Do not insert the speaker system's universal power supply into a

wall outlet until all connections are made. Also, turn off your iPod before

docking on the inMotion system.

To ensure first-time operation as expected, please carefully follow the

connection sequences described below in the order indicated.

Newer iPods can be connected to the inMotion system via the docking port,

while older iPods must be connected using the auxiliary input jack. These

are the only signal input connections that need to be made. After either of

these connections are made, insert the barrel connector from the universal

power supply into the connector marked

inMotion system. After this connection is made, insert the universal power

supply into a wall outlet. You can now use your speakers.

Please note, the inMotion system can also be powered with four AA

batteries (not included). Make sure the batteries are installed as illustrated

in the battery compartments found on the bottom of the inMotion system.

System Specifications

Altec Lansing's superior sound comes from our patented technology, which utilizes custom-built, high-fidelity drivers, state-of-the-art equalization circuitry,

and a harmonious mix of the following specifications:

Total Continuous Power:

• Front Speakers:

Frequency Response:

Signal to Noise Ratio

@ 1 kHz input:

Drivers:

on the rear of the

4 Watts RMS

2 Watts/channel @ 8 ohms

@ 10% THD+N @ 20 – 20 kHz

2 Channels Loaded

60 Hz – 20kHz

> 75 dB

Four 1" full-range

neodymium microdrivers

Headphones

To use headphones with the system, plug them into the jack labeled

on the rear of the inMotion system. When headphones are connected, all

external speakers are muted.

Powering On

AC Power

After your iPod is docked on the inMotion system, plug the universal power

supply into a wall outlet. The speaker system is now ready to operate.

1. Turn on your iPod

2. Turn on the Altec Lansing inMotion system by sliding the power switch

located on the front panel

the switch when the power is on.

Note: To avoid hearing a popping sound when you turn on your Altec

Lansing speaker system, always turn on your audio source first.

DC (Battery) Power

Install four AA batteries (not included) into the battery compartments on

the bottom of the inMotion system (two to each compartment). Make sure

the batteries are installed as illustrated in the battery compartments. After

your iPod is docked on the inMotion system, the speaker system is ready

to operate.

1. Turn on your iPod

2. Turn on the Altec Lansing inMotion system by sliding the power switch

located on the front panel

the button when the power is on. The LED will turn amber in color to

indicate the batteries must be replaced.

Note: To avoid hearing a popping sound when you turn on your Altec

Lansing speaker system, always turn on your audio source first.

Volume

The

buttons on the front of the inMotion system are the master

volume controls for the speaker system. Press and hold the "+" button to

increase the volume and the "–" button to decrease the volume.